DPA BLM6000 Bedienungsanleitung

DPA Mikrofon BLM6000

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für DPA BLM6000 (2 Seiten) in der Kategorie Mikrofon. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
USER’S MANU AL
Type BLM6000
Boundary Layer Mount
DPA Microphones A/S
Gydevang 42-44
DK-3450 Alleroed, Denmark
Tel: +45 4814 2828
Fax: +45 4814 2700
info@dpamicrophones.com
www.dpamicrophones.com
DP I-B LM6000
Physical dimensions:
Diameter: 75 mm
Height: 6 mm
Weight (w/o mic): 12 grams
Order numbers:
BLM6000-B, Black
BLM6000-W, White
Note: Tape not included. Take care to
select tape that will not damage the surface
it is placed on.
have to temporarily remove the microphone
grid (see picture). When you mount the
microphone in the BLM, be sure that the
mesh is completely hidden, so there are no
openings, as they will affect the sound.
Please note: The microphones must be
mounted with the short grid (soft boost
grid). The long grid will not fit into the disc.
Using the Boundary Layer Mount
When mounted in the BLM6000 you can
put the microphone on all surfaces that
reflect sound i.e. tables, lecterns, etc. Even
floors, walls and ceilings are very effective
as boundaries when the BLM6000 is
attached to it.
In general
The pressure zone principle will be more
prominent in a larger frequency range, the
larger the surface the BLM6000 is placed
on. Conversely, you can experiment with a
placement close to the edges of a table, to
the edge of the stage floor or lectern in order
to obtain bass roll off.
If you want to place the disc on a ceiling or
a wall, simply use double-sided tape.
Please find some graphs that illustrate the
frequency response of the microphone
mounted in the BLM.
The BLM6000 is an accessory that will
extend the use of your DPA miniature
microphones i.e. DPA 4060, 4061, 4062,
and 4063.
By placing a microphone close to a reflec-
tive boundary, you will benefit from the
special characteristics of the sound field
found here: a 6 dB gain of direct sound and
only 3 dB gain of the diffuse sound. This
means that the sound picked up has both
greater clarity and intelligibility compared to
the sound picked up in "free air".
Mounting the microphone
It is very important to mount the micro-
phone correctly! If not the sound may suffer
from colouration.
The smoothest frequency response is
achieved with the diaphragm perpendicular
to the reflecting boundary. In order to iden-
tify the position of the membrane you may
USER’S MANU AL
Type BLM6000
Boundary Layer Mount
Frequency response
Sens.
20
15
10
5
0
-5
20
-15
-20
20 31,5 63 125 250 500
Smaller boundary area
Limited boundary area
Larger boundary area
Innite boundary area
Freq.
BLM6000 BLM6000 on floor BLM6000 on desk
BLM6000 mounted on piano lid
DPA4060 in BLM6000 measured on
floor re same microphone measured
in free field position
Typical low frequence response of
DPA4060 in BLM6000 in relation to
the boundary area
BLM6000, rear view
Freq.
Frequency response
Sens.
20
15
10
5
0
-5
20
-15
-20
250 500 1K 2K 5K 10K 20K
Mounting the microphone


Produktspezifikationen

Marke: DPA
Kategorie: Mikrofon
Modell: BLM6000

Brauchst du Hilfe?

Wenn Sie Hilfe mit DPA BLM6000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Mikrofon DPA

Bedienungsanleitung Mikrofon

Neueste Bedienungsanleitung für -Kategorien-