Dimplex ZAM20 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dimplex ZAM20 (4 Seiten) in der Kategorie Kamin. Dieser Bedienungsanleitung war für 81 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
08/19760/1 (UK) Issue 1
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
CASTILLO CST20
ZAMORA ZAM20
1 2 3
I
I
I
II II
II
II
II
II
1
4
32
5
603
665
226
603
665
226
Castillo CST20 Zamora ZAM20
Castillo CST20 & Zamora ZAM20
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical shock,
and injury to persons, including the following:
If the appliance is damaged, check with the supplier before
installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or
swimming pool.
Do not locate the heater immediately below a fixed socket outlet
or connection box.
Do not cover the heater. Do not place material or garments on
the heater, or obstruct the air circulation around the heater, for
instance by curtains or furniture, as this could cause
overheating and a fire risk.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it safely.
Children should be supervised to ensure that they do not play
with the appliance.
Do not use this heater in series with a thermal control, a program
controller, a timer or any other device that switches on the heat
automatically, since a fire risk exists when the heater is
accidentally covered or displaced.
Ensure that furniture, curtains or other combustible material
are positioned no closer than 1 metre from the heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we do
not recommend its use on deep pile carpets or on long hair
type of rugs.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified person
in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the fire to your supplier. Loose
coals and pebbles are packed separately within the carton. When the
heater is assembled the coals or pebbles are placed on top of the fuel
bed up to a maximum weight of 6kg.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the flame effect on its own only requires little electricity.
These models are designed to be free standing and are normally
positioned against a wall.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for
concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage marked
on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
Instructions.
Controls - see Fig. 2
Three switches provide a choice of heat settings. A switch is in the ON
position when the side with the markings on (i.e. I I, , or II) is pushed in.
Switch 1 (I) Controls the electricity supply to the heater and flame
effect.
Note: This switch must be in the ON (I) position for
heater to operate with or without heat.
Switch 2 (I) Provides 1kW heat output
Switch 3 (II) Provides 2kW heat output with switch 2
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent damage
due to overheating. This can happen if the heat outlet was restricted in
any way. The heater will switch on once the obstruction has been
removed and the heater has cooled. If the cut-out continues to operate
intermittently, the heater should be switched off and a service agent
contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Lamp Replacement - see Fig.’s 3, 4 & 5
There are two lamps located beneath the fuel effect. To gain access to
the lamps, remove the coal/pebbles and place in a container. Remove
the front fret/fuel effect from the fire by lifting it up and out from the
slots on the fire - see Fig. 3.
Remove the rotisserie by carefully sliding the rubber connecter off the
motor shaft - see Fig. 4.
Remove the defective lamp by unscrewing it as shown in Fig. 5.
Replace with a 60W E14 SES Clear Candle lamp. Take care not to
over-tighten the lamp.
Refit the front fret/fuel effect and replace the coal/pebbles.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully with a
soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment of
a vacuum cleaner should occasionally be used to clean the outlet grille
of the fan heater.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it
has been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0870 727 0101. It would assist us if you can
quote the model number, series, date of purchase, and nature of the
fault at the time of your call. The customer services help desk will also
be able to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.
Produktspezifikationen
| Marke: | Dimplex |
| Kategorie: | Kamin |
| Modell: | ZAM20 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Dimplex ZAM20 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Kamin Dimplex
20 Mai 2024
8 April 2024
25 März 2024
19 März 2024
11 März 2024
5 März 2024
28 Februar 2024
7 Februar 2024
8 Januar 2024
3 Januar 2024
Bedienungsanleitung Kamin
- Kamin Domo
- Kamin Tristar
- Kamin Cotech
- Kamin Ardes
- Kamin Klarstein
- Kamin Smeg
- Kamin Eurom
- Kamin Fieldmann
- Kamin Qlima
- Kamin Faber
- Kamin Tepro
- Kamin EWT
- Kamin Dovre
- Kamin Invicta
- Kamin La Nordica
- Kamin Blumfeldt
- Kamin Wamsler
- Kamin Hwam
- Kamin Napoleon
- Kamin Furrion
- Kamin Jøtul
- Kamin Edilkamin
- Kamin Firefriend
- Kamin Olsberg
- Kamin Wanders
- Kamin Eligent
- Kamin Planika
- Kamin Blue Rhino
- Kamin Amantii
Neueste Bedienungsanleitung für -Kategorien-
18 August 2024
19 Juni 2024
18 Juni 2024
18 Mai 2024
14 Mai 2024
13 Mai 2024
11 Mai 2024
11 Mai 2024
7 Mai 2024
5 Mai 2024