Dimplex SBN20E Bedienungsanleitung

Dimplex Heizung SBN20E

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dimplex SBN20E (2 Seiten) in der Kategorie Heizung. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Brayford Model: BFD20

547

440

Springborne Model: SBN20

controls

295

547

440

controls

295

Important Safety Advice:

When using electrical appliances, basic precautions

should be followed to reduce the risk of fire, electric

shock, and injury to persons, including the following :

• If the appliance is damaged, check immediately

with the supplier before installation and operation.

• Do not use this heater in the immediate

surroundings of a bath, shower or swimming pool.

• Do not use outdoors.

• This heater must not be located immediately below

a fixed socket outlet or connection box.

• Do not cover or obstruct in any way the heat outlet

grille located at the bottom of the heater.

Overheating will result if the heater is accidentally

covered.

• Ensure that furniture, curtains or other

combustible materials are positioned no closer

than 1 metre from the heater.

• In the event of a fault unplug the heater.

• Unplug the heater when not required for long

periods.

• Keep supply cord away from the front of the

heater.

• Although this heater complies with safety

standards, we do not recommend its use on deep

pile carpets or on long hair type of rugs.

• This appliance is not intended for use by children

or other persons without assistance or

supervision if their physical, sensory or mental

capabilities prevent them from using it safely.

Children should be supervised to ensure that they

do not play with the appliance.

• The appliance must be positioned so that the plug

is accessible.

• If the supply cord is damaged it must be replaced

by the manufacturer or service agent or similarly

qualified person in order to avoid a hazard.

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Fig. 1

General General

Unpack the heater carefully and retain the packaging for possible

future use, in the event of moving or returning the fire to your

supplier.

Unpack the heater carefully and retain the packaging for possible

future use, in the event of moving or returning the fire to your

supplier.

This model is designed to be free standing and is normally

positioned against a wall.

This model is designed to be free standing and is normally

positioned against a wall.

A choice of 1kW or 2kW heat output is provided by the fan heater,

which is located at the bottom of the unit.

A choice of 1kW or 2kW heat output is provided by the fan heater,

which is located at the bottom of the unit.

Before connecting the heater check that the supply voltage is the

same as that stated on the heater.

Before connecting the heater check that the supply voltage is the

same as that stated on the heater.

On the Springborne model loose coals are packed separately within

the carton. When the heater is assembled the coals can be placed

on top of the fuel bed, as required.

On the Springborne model loose coals are packed separately within

the carton. When the heater is assembled the coals can be placed

on top of the fuel bed, as required.

Please note: Used in an environment where background noise

is very low, it may be possible to hear a sound which is related

to the operation of the flame effect. This is normal and should

not be a cause for concern.

Electrical Electrical

WARNING: THIS APPLIANCE MUST BE EARTHED. WARNING: THIS APPLIANCE MUST BE EARTHED.

This fire is suitable for operation on an AC~ electricity supply having

the same voltage as that shown on its rating label.

This fire is suitable for operation on an AC~ electricity supply having

the same voltage as that shown on its rating label.

In the event of replacing the fuse supplied, a 13 amp fuse approved

by ASTA to BS 1362 must be used.

In the event of replacing the fuse supplied, a 13 amp fuse approved

by ASTA to BS 1362 must be used.

If the socket outlets in your home are not of the 13 amp BS1363

type they will not accept the plug connected to this heater, therefore

cut off the plug. When cut off this plug can constitute a shock

hazard if inserted into a socket outlet. It must therefore be disposed

of safely.

If the socket outlets in your home are not of the 13 amp BS1363

type they will not accept the plug connected to this heater, therefore

cut off the plug. When cut off this plug can constitute a shock

hazard if inserted into a socket outlet. It must therefore be disposed

of safely.

Before wiring the appropriate plug please note that the wires in this

mains lead are coloured in accordance with the following code.

Before wiring the appropriate plug please note that the wires in this

mains lead are coloured in accordance with the following code.

GREEN/YELLOW - EARTH GREEN/YELLOW - EARTH

BLUE - NEUTRAL BLUE - NEUTRAL

BROWN - LIVE BROWN - LIVE

Connect the Green/Yellow wire to the terminal marked ‘E’ or the earth symbol or

coloured Green or Green/Yellow.

Connect the Green/Yellow wire to the terminal marked ‘E’ or the earth symbol or

coloured Green or Green/Yellow.

Connect the Brown

wire to the terminal marked ‘

’ or coloured

Red

. Connect the Brown wire to the terminal marked ‘L’ or coloured Red.

Connect the Blue

wire to the terminal marked ‘

’ or coloured

Black

. Connect the Blue wire to the terminal marked ‘N’ or coloured Black.

DO NOT connect the Brown (Live) or the Blue (Neutral) wires to the

Earth terminal of your 13 amp plug. If the terminals of the plug are

unmarked or you are in any doubt, consult a qualified electrician.

DO NOT connect the Brown (Live) or the Blue (Neutral) wires to the

Earth terminal of your 13 amp plug. If the terminals of the plug are

unmarked or you are in any doubt, consult a qualified electrician.

CAUTION: If you use this heater in conjunction with a thermal

control, programme controller, timer or any other device which

switches the heater on automatically observe all safety warnings at

all times

CAUTION: If you use this heater in conjunction with a thermal

control, programme controller, timer or any other device which

switches the heater on automatically observe all safety warnings at

all times

Installation and Operating Instructions

Brayford Log Stove Model: BFD20 08/18740/3 Issue 3

Springborne Coal Stove Model: SBN20

Please note: Used in an environment where background noise

is very low, it may be possible to hear a sound which is related

to the operation of the flame effect. This is normal and should

not be a cause for concern.

Operation

The unique flame effect may be enjoyed whether or not the heating

elements are in operation.

Controls

The heater controls are located on the right hand side of the fan

heater. (see Fig 1)

Three switches provide a choice of heat settings. A switch is in the

ON position when the side with the markings on (i.e. I , I , or II ) is

pushed in.

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility

(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

Glen Dimplex UK Limited UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)

Millbrook House

Grange Drive Customer Services: Tel. 0870 7270101

Hedge End Fax. 0870 7270102

Southampton e-mail customer.services@glendimplex.com

Hampshire. SO30 2DF Republic of Ireland Tel. 01 8424833

[c] Glen Dimplex UK Limited

Fig. 2

Switch 1 ( I ) Controls the electricity supply to the heater and

flame effect.

Note: This switch must be in the ON

( I ) position for heater to operate with or without

heat.

Switch 2 ( I ) Provides 1kW heat output

Switch 3 ( II ) Provides 2kW output with switch 2

Maintenance

WARNING – BEFORE UNDERTAKING ANY MAINTENANCE

OR CLEANING REMOVE PLUG OR

DISCONNECT FROM THE ELECTRICITY

SUPPLY.

Lamp Replacement

Fig. 3

Two lamps are located behind the back panel as indicated in Fig.3.

Fig. 4

To gain access to the lamps, the four screws which secure the back

panel, must be removed. Remove and slide out panel as indicated

on Fig. 4

Fig. 5

Remove the defective lamp by unscrewing it as shown - see Fig. 5.

Replace with a 60W E14 SES Clear Candle lamp.

Take care not to over-tighten the lamp. Refit the back panel and

secure with the four screws.

Safety cut-out

An automatic cut-out will switch off the heater if for any reason it

overheats. This could occur for instance, if the air inlet or outlet were

restricted in any way. If the cut-out operates, the heater will switch

off. The heater will switch on once the obstruction has been

removed and the heater has cooled. If the cut-out continues to

operate intermittently, the heater should be switched off and

Customer Services contacted.

Cleaning

For general cleaning use a soft clean duster – never use abrasive

cleaners. The plastic viewing screen should be cleaned carefully

with a soft cloth. DO NOT use proprietary glass cleaners

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product

free of charge (excluding lamps & subject to availability) provided it

has been installed and operated in accordance with these

instructions.

Your rights under this guarantee are additional to your statutory

rights, which in turn are not affected by this guarantee.

Should you require after sales service you should contact our

customer services help desk on 0870 727 0101. It would assist us if

you can quote the model number, series, date of purchase, and

nature of the fault at the time of your call. The customer services

help desk will also be able to advise you should you need to

purchase any spares.

Please do not return a faulty product to us in the first instance as this

may result in loss or damage and delay in providing you with a

satisfactory service.

Please retain your receipt as proof of purchase.

Produktspezifikationen

Marke:	Dimplex
Kategorie:	Heizung
Modell:	SBN20E
Breite:	440 mm
Tiefe:	310 mm
Gewicht:	14000 g
Produktfarbe:	Schwarz
Steuerung:	Kabellos
Höhe:	545 mm
Verpackungsbreite:	500 mm
Verpackungstiefe:	370 mm
Verpackungshöhe:	610 mm
Fernbedienung enthalten:	Ja
Zertifizierung:	CE, BEAB
Typ:	Elektrischer Raumheizlüfter
Kabellänge:	1.7 m
Anzahl der Leistungsstufen:	2
Regelbare Temperatur:	Ja
Heizleistung:	2000 W
Geeignet für:	Indoor
Platzierungsoptionen:	Flur