DeWalt DW130 Bedienungsanleitung
DeWalt
Drehmaschine
DW130
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr DeWalt DW130 (5 Seiten) in der Kategorie Drehmaschine. Dieser Bedienungsanleitung war fĂźr 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/5
ial Tool Company, 626 Hanover Pike, P.O. Box 158, Hampstead, MD 21074 Printed in U.S.A. (MAY95-CD-6) Form No. 158673-02
or information call toll free between 8:00 a.m. and 8:00 p.m., seven days a week. 1-800-4-D WALT (1-800-433-9258)E
Copyright 1993, 1995
INSTRUCTION MANUAL
DW130 1/2" Drill
W130 5/17/02 3:26 PM Page 2 (Black plate)
F
R
Important Safety Instructions
WARN ING: When using electric tools, basic safety
precautions should always be followed to reduce risk of fire,
electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
Double Insulation
Double insulated tools are constructed throughout with two
separate layers of electrical insulation or one double
thickness of insulation between you and the toolâs electrical
system. Tools built with this insulation system are not
intended to be grounded. As a result, your tool is equipped
with a two prong plug which permits you to use extension
cords without concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal
safety precautions when operating this tool. The insulation
system is for added protection against injury resulting from a
possible electrical insulation failure within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL
REPLACEMENT PARTS. Repair or replace damaged cords.
Polarized Plugs
Polarized plugs (one blade is wider than the other) are used
on equipment to reduce the risk of electric shock. When
provided, this plug will fit in the polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Safety Instructions For All T
â˘KEEP WORK AR E A C LEA N . Cluttered ar
benches invite injuries.
â˘CONSIDER WOR K AR EA E N VIR ON M E N
expose power tools to rain. Donât use power tool
or wet locations. Keep work area well lit. Do not u
presence of flammable liquids or gases.
â˘GUARD AGAINST ELECTRIC SHOCK. Prev
contact with grounded surfaces. For exampl
radiators, ranges, and refrigerator enclosures.
â˘KEEP CHILDREN AWAY. Do not let visitors co
or extension cord. All visitors should be kept a
work area.
â˘STORE IDLE TOOLS. When not in use, tools s
stored in dry, and high or locked-up place â ou
of children.
â˘DONâT FORCE TOOL. It will do the job better an
the rate for which it was intended.
â˘USE RIGHT TOOL. Donât force small tool or attac
do the job of a heavy-duty tool. Donât use tool fo
not intended.
â˘DRESS PROPERLY. Do not wear loose clo
jewelry. They can be caught in moving parts
gloves and non-skid footwear are recommend
working outdoors. Wear protective hair covering
long hair.
â˘USE SAFETY GLASSES. Also use face or dus
operation is dusty.
â˘DONâT ABUSE CORD. Never carry tool by cord
to disconnect from receptacle. Keep cord from
and sharp edges.
BRUSH
SYSTEM
CHUCK
SIDE HANDLE
ROCKER
SWITCH
1
MULTI-POSITION
SPADE HANDLE
âŚBUILT JOBSITE TOUGH
formance industrial tools are made for Americaâs
al and construction applications. The design of every
from drills to sanders to grinders â is the result of
jobsites and throughout industry. Each tool is
ainstaking precision using advanced manufacturing
nse quality control. Every tool is checked before it
ry to make sure that it meets your standards for
y and power.
t Jobsite ToughâŚWE GUARANTEE IT.
ANY QUESTIONS OR COMMENTS
R ANY DEWALT TOOL, CALL US
1-800-4-DEWALT (1-800-433-9258).
m Nameplate Date of Purchase
ormation for future reference.
W130 5/17/02 3:26 PM Page 4 (Black plate)
R
F
Spade Handle Assembly: (Fig. 1)
This spade handle can be attached either horizontally or vertically.
Place the handle into the locating boss on the back of the drill and
assemble with holding knob.
Side Handle (Fig. 1)
The side handle can be placed in either side of the drill or the top of the
drill according to operator preference and available working clearance.
The spade handle can be temporarily removed if working clearance at
rear of tool is limited. Always replace spade handle when possible.
CAUTION: Always use the side handle and switch handle. This is a
high-torque drill. Always hold it firmly with both hands when operating.
FORWARD
REVERSE
TRIGGER SWITCH
LOCK BUTTON âBâ
â˘OUTDOOR USE EXTENSION CORDS. When tool is used
outdoors, use only extension cords intended for use outdoors
and so marked.
â˘STAY ALERT. Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
â˘CHECK DAMAGED PARTS. Before further use of the tool, a
guard or other part that is damaged should be carefully checked
to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service
center. Do not use tool if switch does not turn it on and off.
â˘CAUTION: When drilling or driving into walls, floors or wherever
live electrical wires may be encountered, DO NOT TOUCH ANY
METAL PARTS OF THE TOOL! Hold the tool only by insulated
grasping surfaces to prevent electric shock if you drill or drive into
a live wire.
SAVE THESE INSTRUCTIONS
Motor Brushes
Be sure tool is unplugged before inspecting brushes. To inspect brushes,
unscrew the plastic brush inspection caps (located in the sides of the
motor housing) and withdraw the brush assemblies from the tool.
Keep brushes clean and sliding freely in their guides. Carbon brushes
have varying symbols stamped into them, and if the brush is worn down
to a point where the symbol is not visible, they must be replaced. New
brush assemblies are available at Service Centers; see TOOLS,
ELECTRIC in the Yellow Pages.
NOTE: This tool is designed to automatically turn itself off when the
brushes are worn out.
Switch: (Fig. 2)
Pressing the TOP part of the switch runs the tool in a re
Pressing the BOTTOM part of the switch runs the to
direction. Always let the motor stop completely be
direction.
To lock trigger in âFORWARDâ position, depress LOWE
and push up lock button âBâ. Then, while holding lock bu
gently release trigger. To release locking mechanism,
fully, then release it.
NOTE: Locking mechanism will not function if upper p
depressed (reverse operation).
The locking feature is for use when the drill is mounted i
otherwise firmly held...NOT BY HAND.
Do not lock the switch âONâ when drilling by hand s
instantly release the trigger switch if the bit binds in the
Be sure to release the switch locking button before dis
plug from the power supply. Failure to do so will cause
immediately the next time it is plugged in. Damage
result.
2 3
FIG. 1
ORK. Use clamps or a vise to hold work. Itâs safer
ur hand and it frees both hands to operate tool.
RREACH. Keep proper footing and balance at all
OOLS WITH CARE. Keep tools sharp and clean for
er performance. Follow instructions for lubricating
accessories. Inspect tool cords periodically and if
ve repaired by authorized service facility. Inspect
rds periodically and replace if damaged. Keep
lean, and free from oil and grease.
T OR LOCK OFF TOOLS when not in use, before
when changing accessories, such as blades, bits,
JUSTING KEYS AND WRENCHES. Form habit of
ee that keys and adjusting wrenches are removed
re turning it on.
NTENTIONAL STARTING. Donât carry tool with
ch. Be sure switch is off when plugging in.
CORDS. Make sure your extension cord is in good
hen using an extension cord, be sure to use one
h to carry the current your product will draw. An
rd will cause a drop in line voltage resulting in loss
overheating. The following table shows the correct
epending on cord length and nameplate ampere
oubt, use the next heavier gage. The smaller the
the heavier the cord.
Minimum Gage for Cord Sets
Total Length of Cord in Feet
0-25 26-50 51-100 101-150
0-50 51-100 101-200 201-300
Rating
Not more AWG
Than
6 18 16 16 14
10 18 16 14 12
12 16 16 14 12
16 14 12 Not Recommended
W130 5/17/02 3:26 PM Page 6 (Black plate)
Produktspezifikationen
| Marke: | DeWalt |
| Kategorie: | Drehmaschine |
| Modell: | DW130 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit DeWalt DW130 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Drehmaschine DeWalt
1 Mai 2024
20 April 2024
14 April 2024
14 April 2024
4 April 2024
22 März 2024
18 März 2024
29 Januar 2024
17 Januar 2024
20 November 2023
Bedienungsanleitung Drehmaschine
- Drehmaschine Basetech
- Drehmaschine Panasonic
- Drehmaschine Makita
- Drehmaschine Bosch
- Drehmaschine Parkside
- Drehmaschine Vonroc
- Drehmaschine AEG
- Drehmaschine Powerfix
- Drehmaschine EMOS
- Drehmaschine Black And Decker
- Drehmaschine Cocraft
- Drehmaschine FERM
- Drehmaschine Ryobi
- Drehmaschine Skil
- Drehmaschine Trotec
- Drehmaschine Carrera
- Drehmaschine Hilti
- Drehmaschine Einhell
- Drehmaschine Elu
- Drehmaschine Festool
- Drehmaschine Worx
- Drehmaschine Kraftwerk
- Drehmaschine Hikoki
- Drehmaschine Hitachi
- Drehmaschine Hazet
- Drehmaschine Kress
- Drehmaschine Metabo
- Drehmaschine Stanley
- Drehmaschine GĂźde
- Drehmaschine Biltema
- Drehmaschine Meec Tools
- Drehmaschine Dremel
- Drehmaschine Fieldmann
- Drehmaschine Beta
- Drehmaschine Westfalia
- Drehmaschine Chicago Pneumatic
- Drehmaschine Dedra
- Drehmaschine Silverline
- Drehmaschine Sthor
- Drehmaschine Yato
- Drehmaschine Pansam
- Drehmaschine Bavaria
- Drehmaschine BrĂźder Mannesmann
- Drehmaschine Milwaukee
- Drehmaschine Toolcraft
- Drehmaschine Chamberlain
- Drehmaschine Fein
- Drehmaschine Bonus
- Drehmaschine Craftsman
- Drehmaschine Powerplus
- Drehmaschine Ozito
- Drehmaschine Porter-Cable
- Drehmaschine Steren
- Drehmaschine Wiha
- Drehmaschine StarTech.com
- Drehmaschine Meister Craft
- Drehmaschine Truper
- Drehmaschine Park Tool
- Drehmaschine XU1
- Drehmaschine Urrea
- Drehmaschine Wera
- Drehmaschine VOREL
- Drehmaschine Netter Vibration
- Drehmaschine Rodcraft
- Drehmaschine Bavaria By Einhell
- Drehmaschine SW-Stahl
Neueste Bedienungsanleitung fĂźr -Kategorien-
26 Juni 2024
26 Juni 2024
21 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024
18 Juni 2024