Dell PowerEdge 700 Bedienungsanleitung

Dell Server PowerEdge 700

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dell PowerEdge 700 (94 Seiten) in der Kategorie Server. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/94

Dell™PowerEdge™700SystemsInstallationandTroubleshootingGuide

Introduction

Indicators and Codes

Finding Software Solutions

Running System Diagnostics

Troubleshooting Your System

Installing System Options

Installing Drives

Getting Help

Jumpers and Connectors

I/O Connectors

Abbreviations and Acronyms

Notes, Notices, and Cautions

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see "Abbreviations and Acronyms."

Information in this document is subject to change without notice.

©2003DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, Dell OpenManage, Dell Precision, Dimension, Inspiron, OptiPlex, Latitude, DellNet, PowerVault, PowerApp, and Axim are

trademarks of Dell Inc.; Intel, Pentium, and Celeron are registered trademarks of Intel Corporation; Microsoft, MS- DOS, and Windows are registered trademarks of Microsoft

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Initial release: November 2003

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page



Jumpers and Connectors

Dell™PowerEdge™700SystemsInstallationandTroubleshootingGuide

Jumpers—A General Explanation

System Board Jumpers

System Board Connectors

Disabling a Forgotten Password



This section provides specific information about the system jumpers. It also provides some basic information on jumpers and switches and describes the

connectors on the various boards in the system.



Jumpers—A General Explanation



Jumpers provide a convenient and reversible way of reconfiguring the circuitry on a printed circuit board. When reconfiguring the system, you may need to

change jumper settings on circuit boards or drives.



Jumpers



Jumpers are small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects

the pins and creates a circuit. To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated. FigureA-1 shows an

example of a jumper.

Figure A- 1. Example Jumpers



A jumper is referred to as open or unjumpered when the plug is pushed down over only one pin or if there is no plug at all. When the plug is pushed down

over two pins, the jumper is referred to as jumpered. The jumper setting is often shown in text as two numbers, such as 1–2. The number 1 is printed on the

circuitboardsothatyoucanidentifyeachpinnumberbasedonthelocationofpin1.



FigureA-2 -1 shows the location and default settings of the system jumper blocks. See TableA for the designations, default settings, and functions of the

system's jumpers.



System Board Jumpers



FigureA-2 -1 shows the location of the configuration jumpers on the system board. TableA lists the jumpers settings.

Figure A- 2. System Board Jumpers



CAUTION: Ensure that the system is turned off before you change a jumper setting. Otherwise, damage to the system or unpredictable results

may occur.



Table A-1.SystemBoardJumperSettings



System Board Connectors



See FigureA-3 and TableA-2 -3 for the location and description of system board connectors. FigureA also lists expansion slot numbers, buses, and bus

operating speeds.

Figure A- 3. System Board Connectors



Jumper

Setting

Description

PSWD_EN

 (default)