Deaf Bonce Apocalypse AAB-600.2D Atom Bedienungsanleitung
Deaf Bonce
Empfänger
Apocalypse AAB-600.2D Atom
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Deaf Bonce Apocalypse AAB-600.2D Atom (24 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/24
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/de/deaf-bonce/apocalypse-aab-6002d-atom/html/bg1.png)
https://alphard.audio
AAB- 00. D6 2
TWO-CHANNEL AMPLIFIER
ДВУХКАНАЛЬНЫЙ УСИЛИТЕЛЬ
AAB ATOM
CLASS D
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/de/deaf-bonce/apocalypse-aab-6002d-atom/html/bg2.png)
2
C O N T E N T S EN
1. Introduction
3. Typical installation sequence
2. Safety instructions
4. Selection of the diameter of power cables and speaker cables
6. Connection methods
8. Possible faults and their solutions
9. Box content
10. Warranty and maintenance info
11. Information on disposal of the electrical and electronic equipment (for the European countries
5. Wiring diagrams
with separate waste collection)
7. Specifications
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/de/deaf-bonce/apocalypse-aab-6002d-atom/html/bg3.png)
3
EN
1 . I N T RO D U C T I O N
2. Check the state of on-board power supply of your vehicle, the battery and the alternator. When the engine is running, depending on
the ambient temperature, the voltage to be outputted by the alternator must be within the range of 14 to 14.7 V. Open circuit voltage
(OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the alternator and the battery capacity is
enough to provide increased consumption.
For example, for the power of the amplifier 1000 W, the rated current of the alternator is required at the rate of 1000 W / 13 V = 77
amperes. A more powerful amplifier requires a more powerful alternator as well as an additional battery.
4. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the insulating layer,
short circuit and fire.
5. The amplifier should be installed in areas of the car where the temperature varies from 0 °C (32 °F) to 55 °C (131 °F). The amplifier
should be in a place with a good air circulation. The horizontal position of the amplifier is the best way to install.
3. Do not place the amplifier in the engine compartment and also in the places exposed to water, moisture, dust or dirt.
1. Make sure that your vehicle has a 12V DC electrical system with negative grounding. Before installing the amplifier in cars, trucks or
buses, check the battery voltage.
6. During the operation the amplifier may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated that may
be dangerous.
7. To improve the cooling of the amplifier, it is recommended to clean periodically the heatsink from dust. When cleaning the heatsink
strong solvents should not be used as they may damage the amplifier. Do not use compressed air, because solids can penetrate inside the
amplifier. Cleanings best done with wet towels or cloth.
14. To avoid accidental damage, keep the amplifier in its original packaging prior to installation.
CAUTION!!! High sound pressure can damage your health!
12. Make sure that all the cables are fixed over the entire length. Also make sure that their outer protective shell is non-combustible.
Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the amplifier.
15. Use high-quality copper speaker and power cables.
8. Make sure that the location of the amplifier does not violate the proper operation of mechanical and electrical devices of the vehicle.
9. Make sure that during the installation and connection of the battery, the power cables are not shorted.
11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the
parts exposed to heat.
Please use the common sense when controlling volume!
10. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe or other
structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
13. Select a diameter of the power cable in accordance with the power of the amplifier and the recommendations provided here.
Power cables are extremely important since they directly affect the system damping factor and sound quality. The cables to the battery
must be in the copper crimp terminals pressed with the help of a hydraulic press, and well fixed to the battery terminals.
2 . S A F E T Y I N S T R U C T I O N S
3 . T Y P I C A L I N S TA L L AT I O N S E Q U E N C E
12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the
sensitivity level of the amplifier up until you hear distortions.
2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation
of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: see Table: Selection of the diameter
of the power cables)
7 To connect the power wire supply is necessary to use special. power cables.
3. Connect the power supply with the correct polarity. Connect all (+) terminals of the amplifier to the cables stretching from
the positive terminal of the battery and all (-) terminals of the amplifier – to the cables stretching from the negative terminal of the
battery.
5. Route all signal cables next to each other and separately from the power cables.
9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.
Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the
light bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive
terminal of the battery.
6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V.
8. Fasten the amplifier properly when installing it in the vehicle. If the component is disconnected during driving, it may cause
serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the amplifier directly to the
metal it can lead to distorsions at the signal outputs.
4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of
the power cable to the holder after connecting the other end to the amplifier. Do not install the fuse(s).
When properly connected, the bulb must briefly light up and go out. Now you may connect the positive lead to the (+) of the
battery. If the light does not go out, then something is wrong. This will prevent damage to the amplifier in case of reverse polarity
and unwanted sparks when connecting. Install the rest of the fuses.
10 . To activate the amplifier, it is necessary to apply the positive potential of 12 volts to the control input of the amplifier (REM
IN) through a switch or a corresponding control output (REMOTE ) with the head unit (HU).
1. Before installing the amplifier disconnect the battery from the electrical system.
11. LED indicator on front of the amplifier turns blue to indicate that the amplifier is turned on. If the indicator does not light
up see chapter "Possible faults and their solutions" for more information.
Thank you for purchasing this Deaf Bonce product! Our company is committed to the creation of of extremely loud sound
systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you
read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.
Produktspezifikationen
Marke: | Deaf Bonce |
Kategorie: | Empfänger |
Modell: | Apocalypse AAB-600.2D Atom |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Deaf Bonce Apocalypse AAB-600.2D Atom benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger Deaf Bonce
![Deaf Bonce](/images/pdf_free.png)
7 April 2024
![Deaf Bonce](/images/pdf_free.png)
21 Februar 2024
![Deaf Bonce](/images/pdf_free.png)
13 Februar 2024
![Deaf Bonce](/images/pdf_free.png)
7 Februar 2024
![Deaf Bonce](/images/pdf_free.png)
19 Januar 2024
![Deaf Bonce](/images/pdf_free.png)
12 Januar 2024
Bedienungsanleitung Empfänger
- Empfänger Hama
- Empfänger Audio-Technica
- Empfänger Manhattan
- Empfänger Medion
- Empfänger Sony
- Empfänger Panasonic
- Empfänger Roland
- Empfänger Bosch
- Empfänger Vox
- Empfänger TechniSat
- Empfänger Yamaha
- Empfänger Devolo
- Empfänger Schwaiger
- Empfänger Gira
- Empfänger König
- Empfänger Renkforce
- Empfänger Trevi
- Empfänger Blaupunkt
- Empfänger Grundig
- Empfänger Kenwood
- Empfänger Hilti
- Empfänger Pyle
- Empfänger Golden Age Project
- Empfänger Salora
- Empfänger Telestar
- Empfänger Bose
- Empfänger Caliber
- Empfänger Denon
- Empfänger Pioneer
- Empfänger Jabra
- Empfänger JBL
- Empfänger JVC
- Empfänger Klipsch
- Empfänger Meliconi
- Empfänger Nokia
- Empfänger Onkyo
- Empfänger Sennheiser
- Empfänger Shure
- Empfänger Technics
- Empfänger Hifonics
- Empfänger Akai
- Empfänger Alden
- Empfänger Dual
- Empfänger Ferguson
- Empfänger Hyundai
- Empfänger Strong
- Empfänger Tesla
- Empfänger Imperial
- Empfänger Garmin
- Empfänger Sencor
- Empfänger Plantronics
- Empfänger Fenton
- Empfänger TOA
- Empfänger Rotel
- Empfänger Musway
- Empfänger Tripp Lite
- Empfänger Harman Kardon
- Empfänger Magnat
- Empfänger Marmitek
- Empfänger Marshall
- Empfänger Power Dynamics
- Empfänger Samson
- Empfänger Skytec
- Empfänger Vonyx
- Empfänger Peavey
- Empfänger Xoro
- Empfänger Atlas
- Empfänger Edision
- Empfänger GigaBlue
- Empfänger Kathrein
- Empfänger Topfield
- Empfänger Zehnder
- Empfänger Icom
- Empfänger Alpine
- Empfänger NAD
- Empfänger Renegade
- Empfänger Vision
- Empfänger Behringer
- Empfänger Omnitronic
- Empfänger MB Quart
- Empfänger Marantz
- Empfänger Arcam
- Empfänger Cambridge
- Empfänger Crown
- Empfänger Dynacord
- Empfänger Luxman
- Empfänger Monacor
- Empfänger Rockford Fosgate
- Empfänger TEAC
- Empfänger Crunch
- Empfänger Sangean
- Empfänger Revox
- Empfänger Mac Audio
- Empfänger T-Mobile
- Empfänger August
- Empfänger Audison
- Empfänger DataVideo
- Empfänger RCF
- Empfänger Electro-Voice
- Empfänger Delta Dore
- Empfänger Sonos
- Empfänger Yorkville
- Empfänger MIPRO
- Empfänger Elektrobock
- Empfänger Boss
- Empfänger Intertechno
- Empfänger Alto
- Empfänger Chord
- Empfänger Kramer
- Empfänger Hertz
- Empfänger Pro-Ject
- Empfänger Galaxy Audio
- Empfänger HQ Power
- Empfänger Kicker
- Empfänger Warm Audio
- Empfänger Line 6
- Empfänger Bogen
- Empfänger DBX
- Empfänger McIntosh
- Empfänger Jensen
- Empfänger ELAC
- Empfänger JL Audio
- Empfänger Qtx
- Empfänger Hartke
- Empfänger ART
- Empfänger Fredenstein
- Empfänger LD Systems
- Empfänger Black Lion Audio
- Empfänger GlobalSat
- Empfänger DAP Audio
- Empfänger Devialet
- Empfänger Focal
- Empfänger Focusrite
- Empfänger Formuler
- Empfänger Fusion
- Empfänger Ground Zero
- Empfänger Infinity
- Empfänger JB Systems
- Empfänger Lanzar
- Empfänger Mercury
- Empfänger Mtx Audio
- Empfänger Mvision
- Empfänger Octagon
- Empfänger Phoenix Gold
- Empfänger Stagg
- Empfänger Steren
- Empfänger ACV
- Empfänger TV STAR
- Empfänger Universal Remote Control
- Empfänger Winegard
- Empfänger Adastra
- Empfänger Siig
- Empfänger Amiko
- Empfänger Mooer
- Empfänger AudioControl
- Empfänger TV One
- Empfänger StarTech.com
- Empfänger APart
- Empfänger Blackstar
- Empfänger HEOS
- Empfänger QSC
- Empfänger Niles
- Empfänger Martin Logan
- Empfänger Metra
- Empfänger Sound Devices
- Empfänger Speco Technologies
- Empfänger IFi Audio
- Empfänger Gefen
- Empfänger Polsen
- Empfänger SRS
- Empfänger Mosconi
- Empfänger Atlas Sound
- Empfänger Micromega
- Empfänger Palmer
- Empfänger Ampeg
- Empfänger Avalon
- Empfänger Lectrosonics
- Empfänger Citronic
- Empfänger Crest Audio
- Empfänger Lab Gruppen
- Empfänger SPL
- Empfänger Parasound
- Empfänger Axis
- Empfänger Wet Sounds
- Empfänger Edisio
- Empfänger Pyramid
- Empfänger Stewart
- Empfänger Linn
- Empfänger Audac
- Empfänger OSD Audio
- Empfänger Audioengine
- Empfänger BZBGear
- Empfänger Crestron
- Empfänger Atlona
- Empfänger JTS
- Empfänger Valueline
- Empfänger Ashdown Engineering
- Empfänger Ram Audio
- Empfänger Esoteric
- Empfänger Sonifex
- Empfänger Advance Acoustic
- Empfänger Lindell Audio
- Empfänger Acme United
- Empfänger Mark Levinson
- Empfänger Dynavox
- Empfänger Ocean Matrix
- Empfänger LEA
- Empfänger Memphis Audio
- Empfänger FiveO
- Empfänger Ashly
- Empfänger Matrox
- Empfänger CyberData Systems
- Empfänger SoundTube
- Empfänger ANKARO
- Empfänger NUVO
- Empfänger AMS Neve
- Empfänger Trace Elliot
- Empfänger The T.amp
- Empfänger Camille Bauer
- Empfänger Dimavery
- Empfänger Musical Fidelity
- Empfänger Fosi Audio
Neueste Bedienungsanleitung für -Kategorien-
![Dimavery](/images/pdf_free.png)
18 April 2024
![TOA](/images/pdf_free.png)
17 April 2024
![Pioneer](/images/logos/pioneer.png)
17 April 2024
![NAD](/images/pdf_free.png)
16 April 2024
![Devialet](/images/pdf_free.png)
16 April 2024
![Cambridge](/images/pdf_free.png)
16 April 2024
![AudioControl](/images/pdf_free.png)
16 April 2024
![RCF](/images/pdf_free.png)
16 April 2024
![Zehnder](/images/pdf_free.png)
15 April 2024
![Marantz](/images/pdf_free.png)
15 April 2024