DCS CAD1-SK Bedienungsanleitung

DCS Grill CAD1-SK

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für DCS CAD1-SK (4 Seiten) in der Kategorie Grill. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
1
IMPORTANT:
Read all instructions before you begin. Do not jump ahead or skip any step.
CAUTION:
Some parts have sharp edges; care must be taken when handling the various components to
avoid injury. Be sure to use adequate manpower to assemble and install the side shelf to prevent
personal injury or damage to the unit.
NOTE: Avoid using side shelf to move cart. Push or pull cart by grasping corners of grill head. Never attempt to move a
hot grill. Allow unit to cool before touching.
GETTING STARTED
Remove packaging.
Contents Included:
Your side shelf is packaged in one box. The box contains your side
shelf, brackets, and installation hardware.
Tools Required:
Item No. Description Quantity
1
1
1
2
2
2
Shelf
(optional)
Work Gloves
5/32” Allen Wrench
3/16” Allen Wrench
Power Screwdriver or
Variable Speed Drill
with Phillips - tip
#2 Attachment
Bracket, Shelf-left
3/32” Allen Wrench
Bracket, Shelf-right
Bolt Shoulder, 5/16 x 1/4-20
Shoulder Bolt, 3/8 x 3/8 x 5/16-18
Screw, 10-24 X 1-1/8
1
2
5
3
4
6
SIDE SHELF (CAD-SK 70853)
INSTALLATION INSTRUCTIONS
1
2
3
4
5
6
Eye Protection
Fig. 03 Fig. 04
Attach Side Shelf Accessory on Either Side
NOTE: Side shelf Model CAD-SK can be installed with the head already on the cart.
1. Screw shoulder bolts (2) into the bottom screw holes on the side of the cart (Fig. 01 and 02). Tighten with 5/32
Allen wrench.
2. Slide left and right side shelf brackets over the shoulder bolt (Fig. 03) and install top screw attaching the side
shelf brackets onto the cart (Fig. 04). Tighten with Phillips screwdriver.
Fig. 01 Fig. 02
SHOULDER BOLT
SCREW HOLES
LEFT BRACKET
SCREW
2
3. Holding the side shelf, install 2 shoulder bolts (3/8 shoulder bolt) through the slots on the side shelf brackets into
the threaded holes on the side of the side shelf tray (Fig. 05). Tighten with a 3/16 Allen wrench (Fig. 06).
4. Locate the cart on flat level ground before attempting to level the side shelves. Place shelf in the up position and
check that it is level.
If the shelf is not level, adjust side shelf set screws. The set screws can be adjusted using a 3/32 Allen wrench
(Fig. 07). Turn the Allen wrench clockwise to raise the shelf. Turn 1/4 turn and review to see if the shelf is level.
The set screws in the left and right bracket should be adjusted equally to ensure the shelf sits level (Fig. 08).
Optional wood cutting board (model # CAD-WBC, 70861) shown in Figure 09 can be purchased as an accessory
from Customer Care at (888) 281-5698.
3
Fig. 07
Fig. 05 Fig. 06
Fig. 08
Fig. 09


Produktspezifikationen

Marke: DCS
Kategorie: Grill
Modell: CAD1-SK

Brauchst du Hilfe?

Wenn Sie Hilfe mit DCS CAD1-SK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Grill DCS

Bedienungsanleitung Grill

Neueste Bedienungsanleitung für -Kategorien-