CyberPower RB1290X16 Bedienungsanleitung

CyberPower Batterie RB1290X16

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberPower RB1290X16 (3 Seiten) in der Kategorie Batterie. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

1 2 3

123

MODEL: OR1500LCDRM2U, OR2200LCDRM2U, OR1500LCDRTXL2U,

MODEL: PR1000LCD

MODEL: PR1500LCD

1. Remove the front panel of the UPS.

2. Remove two screws from the battery compartment cover and slide the cover completely off of

the unit.

3. Remove the batteries from the compartment. Disconnect the battery wires from the batteries.

4. Install the replacement batteries by connecting the wire bundle (composed of one red wire and

one black wire) to the connector from the battery pack.

5. Put the batteries back into the compartment. Re-install the battery compartment cover and

tighten the retaining screws. Put the front panel back on the UPS.

6. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge

MODEL: PR750LCDRM1U, PR1000LCDRM1U

1. Remove the right side front panel.

2. Remove the two retaining screws for the cable protection cover and remove the cover.

3. Disconnect the black and red cable.

4. Remove the one retaining screw holding the battery pack in place.

5. Remove the battery pack.

6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

sequence of the above steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR1500SWRM2U, PR2200SWRM2U

1. Remove the right side front panel.

2. Remove the two retaining screws for the cable protection cover and remove the cover.

3. Disconnect the black and red cable.

4. Remove the four retaining screws holding the battery pack in place.

5. Remove the battery pack.

6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR1000LCDRT2U, PR1000LCDRTXL2U, PR1500LCDRT2U,

PR2200LCDRT2U, PR3000SWRM2U

1. Remove the right side front panel.

2. Remove the three retaining screws for the cable protection cover and remove the cover.

3. Remove the two retaining screws from the cable connectors.

4. Disconnect the black and red cable.

5. Remove the four retaining screws holding the battery pack in place.

6. Remove the battery pack.

7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR1000LCDRTXL2Ua, PR1500LCDRTXL2U, PR2200LCDRTXL2U,

PR3000LCDRT2U, PR3000LCDRTXL2Umart

1. Remove the six retaining screws, and remove the front panel from the UPS.

2. Remove the two retaining screws for the cable protection cover and remove the cover.

3. Remove the two retaining screws from the cable connectors.

4. Disconnect the black and red cable.

5. Remove the three retaining screws holding the battery pack in place.

6. Remove the battery pack.

7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

MODEL: PR5000LCDRTXL5U, PR6000LCDRTXL5U

1. Remove the front panel.

2. Remove the two retaining screws of the cable protection cover and remove the cover.

3. Pull the plastic sticker out slowly to remove the battery module.

4. Put the new battery modules back into the compartment.

5. Tighten the screws and replace the cable protection cover and the front panel.

PFC SINEWAVE Series

MODEL: CP850PFCLCD, CP1000PFCLCD

1. Turn the UPS on its side. Remove the retaining screw located on the bottom of the UPS.

2. Slide the battery compartment cover completely off of the unit.

3. Remove the batteries from the compartment.

4. Disconnect the battery wires from the batteries.

5. Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same

color connectors from the battery pack. Put the batteries back into the compartment.

6. Slide back the battery compartment cover and tighten the retaining screw. Recharge the UPS

for 8-16 hours to fully charge the battery.

MODEL: CP1350PFCLCD

1. Turn the UPS on its side. Remove the front panel retaining screws located on the bottom of the

UPS.

2. Slide the battery compartment cover (front panel) completely off of the unit.

3. Remove the batteries from the compartment.

4. Disconnect the battery wires from the batteries.

5. Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same

color connectors from the battery pack. Put the batteries back into the compartment.

6. Slide back the battery compartment cover and tighten the retaining screws. Recharge the UPS

for 8-16 hours to fully charge the battery.

MODEL: CP1500PFCLCD

1. Turn the UPS on its side. Remove the front panel retaining screws located on the bottom of the

UPS.

2. Slide the battery compartment cover (front panel) completely off of the unit.

3. Remove the batteries from the compartment.

4. Disconnect the battery wires from the batteries.

5. Install the replacement batteries by connecting the wire bundle (composed of one red wire and

one black wire) to the connector from the battery pack. Put the batteries back into the

compartment.

6. Slide back the battery compartment cover and tighten the retaining screws. Recharge the UPS

for 8-16 hours to fully charge the battery.

MODEL: OR1500PFCRT2U, OR2200PFCRT2U

1. Remove the right side front panel.

2. Remove the three retaining screws for the cable protection cover and remove the cover.

3. Remove the two retaining screws from the cable connectors.

4. Disconnect the black and red cable.

5. Remove the four retaining screws holding the battery pack in place.

6. Remove the battery pack.

7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse

order of the previous steps. Charge the unit for 4-8 hours to ensure the UPS performs expected

runtimes.

Produktspezifikationen

Marke:	CyberPower
Kategorie:	Batterie
Modell:	RB1290X16
Akku-/Batteriekapazität:	9000 mAh
Breite:	540 mm
Tiefe:	400 mm
Gewicht:	49305 g
Akku-/Batterietechnologie:	Plombierte Bleisäure (VRLA)
Höhe:	378 mm
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 90 %
Verpackungsbreite:	642 mm
Verpackungstiefe:	330 mm
Verpackungshöhe:	393 mm
Paketgewicht:	4132625 g
Akku-/Batteriespannung:	12 V
Kompatible Produkte:	PR5000LCDRTXL5U, PR6000LCDRTXL5U
Kompatibilität:	PR5000LCDRTXL5U, PR6000LCDRTXL5U
Anzahl enthaltener Akkus/Batterien:	16 Stück(e)