Crestron Essence IW5-W-T Bedienungsanleitung

Crestron Lautsprecher Essence IW5-W-T

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Crestron Essence IW5-W-T (2 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war fĂĽr 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Essence™ In-Wall Speakers
quickstart guide
IW5, IW6, IW8
www.crestron.com
Specifications subject to
change without notice.
IW5, IW6, IW8
Mount/Remove Speakers
The in-wall speakers include six toggle clamps that simplify the mounting process. If the
grilles are mounted on the speakers, remove them before proceeding. (Refer to “Install/
Remove Grilles”, below.)
1. Connect the speaker cable wires to the spring terminals by pressing the top of the
terminals down and inserting the exposed strands into the hole. Make sure that the
+ + – – wires go to the (red coded) terminals, and the wires go to the (black coded)
terminals.
2. With the toggle clamps turned inward, insert the speaker into the opening. As the six
screws on the front of the speaker are tightened, the toggle clamps first rotate into
clamping position (refer to the figure to the right) and then begin holding the speaker
to the wall. Tighten the screws until the speaker is secured; do not overtighten.
3. Speaker removal is accomplished by reversing the procedures given in steps 1 and 2
above.
a. Loosen the front screws to unclamp the speaker. Continue to loosen the screws
until the toggle clamps rotate inward.
b. When the speaker is loose, carefully remove it from the opening.
c. Disconnect the wires from the terminals.
Install/Remove Grilles
The zero-bezel frameless grilles are held in place by powerful magnets. To remove the
grilles, grip the edges and pull away from the speaker.
1
1Installation
The product of expert Crestron® audio engineering,
Essence™ speakers deliver the pinnacle of performance
for demanding residential installations. Select esoteric
materials, top shelf components and a refined, high-end
appearance underscore the meticulous design behind
each model. The result is a complete line of in-wall and
in-ceiling speakers worthy of a place in every room of
the finest custom home.
QUICKSTART DOC. 7394B (2034614) 12.12
Determine Placement In Room
Rear View (Typical)
Install Cables
Run the cables from the audio source to each speaker location following all appropriate
local codes. Strip the ends of the speaker cable wires 1/4” to 1/2” (6 mm to 12 mm) and
twist the exposed strands.
Spring
Terminals (2)
Toggle
Clamps (6)
Tighten
Screws
The Essence line promises the ultimate in installed audio
design, delivering simply stunning sound quality while
minimizing any impact on your décor thanks to paintable
zero-bezel grilles.
Speaker placement is largely a matter of personal preference. However, placing the speaker
near a corner will extend its low frequency response.
Prepare Mounting Holes
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air
ducts, joists, or other possible obstructions. Use a good quality stud finder to locate joists.
If there is no access to the area behind the wall, and it is uncertain that there are no
obstructions, carefully drill a small hole just through the wall near the middle of the proposed
speaker location(s) and use one of the commercially available inspection devices designed for
this purpose, or do one of the following:
● Use a piece of stiff wire, bent into an “L” shape, with one end long enough to explore an
area equal to the size of the speaker with the toggle clamps extended. Insert the wire into
the hole, make sure it rotates freely in a complete circle and that there is sufficient depth,
or
● Use a drywall saw to cut a small hole at a 45° angle toward the inside of the hole. An
angle cut simplifies repair since the removed piece can be reinserted to help plug the hole.
90°
If there are no obstructions, use the supplied template to trace outlines of the mounting holes
on the wall. Cut the final mounting holes at a 90° angle to the wall.
Paint the Speaker Grilles
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grilles and set them aside for
reinstallation. It may be necessary to use a knife or other sharp instrument to free
an edge of the material so it can be peeled away. Use care to avoid cutting or
tearing the material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the
holes in the grilles.
3. Once the paint is dry, reinstall the material to the underside.
Front View (Typical)
45°
Essence™ In-Wall Speakers
quickstart guide
IW5, IW6, IW8
www.crestron.com
Specifications subject to
change without notice.
IW5, IW6, IW8
Specifications
QUICKSTART DOC. 7394B (2034614) 12.12
2
2
IW5, IW6, IW8 Specifications
Features & Performance
Woofer1
Tweeter2
Crossovers
Crossover Frequency
Environmental
Temperature
Humidity
Dimensions3
Height
Width
Depth
Minimum Mounting Depth
Recommended Cutout Size
Impedence
Frequency Response
Frequency Range
Power Handling
Sensitivity
Construction
Baffle
Grille
Mounting
8 Ω nominal
55 Hz - 20 kHz (±3 dB)
45 Hz to 20 kHz (-10 dB)
125 watts program
88.5 dB @ (W/m)
IW5
10.42 in (265 mm)
7.90 in (201 mm)
3.27 in (83 mm)
3.10 in (79 mm)
9.80 in (249 mm) high,
7.30 in (186 mm) wide
ABS plastic, black
Steel with textured finish, paintable, magnetically-held “zero bezel” frameless
Flush wall mount using six integral spring-loaded toggle clamps, 1.35 in (34 mm)
maximum surface thickness
41° to 104° F (5° to 40° C)
10% to 90% RH (non-condensing)
For indoor use only
Connections
Input
Maximum Wire Size
(2) spring terminals
10 AWG
IW6 IW8
5.25 in (134 mm)
1.10 in (28 mm)
4th order Linkwitz-Riley
2 kHz
1. Woven Kevlar
® with rubber surround, vented pole piece and cast aluminum basket
2. Advanced synthetic polymer dome, ferrofluid cooling, damped aperiodic rear chamber
3. Dimensions shown are per speaker, positioned vertically
8 Ω nominal
45 Hz - 20 kHz (±3 dB)
35 Hz to 20 kHz (-10 dB)
150 watts program
89.0 dB @ (W/m)
6.50 in (165 mm)
1.10 in (28 mm)
4th order Linkwitz-Riley
2 kHz
8 Ω nominal
38 Hz - 20 kHz (±3 dB)
30 Hz to 20 kHz (-10 dB)
175 watts program
91.5 dB @ (W/m)
8.00 in (203 mm)
1.10 in (28 mm)
4th order Linkwitz-Riley
2 kHz
Weight35.26 lb (2.4 kg)
Available Models
Available Accessories
Essence 5.25” 2-Way
In-Wall Speaker, Pair,
White Textured
ESSENCE IW5-W-T
SPKA-NCTP-IW500
New-Construction
Speaker Templates
11.86 in (301 mm)
8.98 in (228 mm)
3.67 in (94 mm)
3.49 in (89 mm)
11.20 in (285 mm) high,
8.30 in (211 mm) wide
5.74 lb (2.6 kg)
13.91 in (354 mm)
10.45 in (266 mm)
4.50 in (115 mm)
4.33 in (110 mm)
13.30 in (338 mm) high,
9.80 in (249 mm) wide
7.54 lb (3.4 kg)
Essence 6.5” 2-Way
In-Wall Speaker, Pair,
White Textured
ESSENCE IC6-W-T
SPKA-NCTP-IW600
New-Construction
Speaker Templates
Essence 8” 2-Way
In-Wall Speakers, Pair,
White Textured
SPKA-NCTP-IW800
New-Construction
Speaker Templates
SPECIFICATION
ESSENCE IC6-W-T
Height
Cutout
Height
Width
Cutout
Width
Depth
Minimum
Mounting
Depth
Side and Rear Views (Typical)
The following table provides corrective action for possible trouble situations.
If further assistance is required, please contact a Crestron customer service
representative.
Further Inquiries
Future Updates
TROUBLE
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
No sound or
intermittent
sound from
speakers.
Cable connection
error.
Verify cable connections
between amplifier and speakers.
Amplifier not receiving
input signal or amplifier
malfunction.
Verify amplifier is functioning correctly,
that it is receiving an input signal and
that correct input source is selected.
Faulty device in system. Verify all devices in system are
functioning properly.
Constant
noise such as
buzz, hum, or
hiss from
speakers.
System grounding fault. Verify system grounding.
Poor low
frequency
output.
Incorrect polarity
connection at speaker.
Verify speaker connection polarity
(+ on speaker to + on amplifier).
3Problem Solving
Troubleshooting
To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876]
or refer to the listing of Crestron worldwide offices on the Crestron Web site
(www.crestron.com/offices) for assistance within a particular geographic
region.
To post a question about Crestron products, log onto the Online Help section
of the Crestron Web site (www.crestron.com/onlinehelp).
First-time users
must establish a user account to fully benefit from all available features.
As Crestron improves functions, adds new features and extends the
capabilities of the Essence IW5, IW6, and IW8, additional information may
be made available as manual updates. These updates are solely electronic
and serve as intermediary supplements prior to the release of a complete
technical documentation revision.
Check the Crestron Web site periodically for manual update avail
ability and
its relevance. Updates are identified as an “Addendum” in the Download
column.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo and Essence, are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. Kevlar is either a trademark or registered trademark of E. I. du Pont
de Nemours and Company in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims proprietary interest in the marks and names of others.
©2012 Crestron Electronics, Inc.


Produktspezifikationen

Marke: Crestron
Kategorie: Lautsprecher
Modell: Essence IW5-W-T

Brauchst du Hilfe?

Wenn Sie Hilfe mit Crestron Essence IW5-W-T benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Crestron

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung fĂĽr -Kategorien-