CDA KA30SS Bedienungsanleitung

CDA Spülbecken KA30SS

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CDA KA30SS (3 Seiten) in der Kategorie Spülbecken. Dieser Bedienungsanleitung war für 46 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

www.cda.eu

ka30, ka32,

ka80 and ka82

Stainless Steel

Sinks

Installation

Before Installation

Oer up the sink to the worktop and/or the cabinets to conﬁrm that

the external dimensions of the bowls are compatible with the cabinets

themselves.

Conﬁrm that with the sink in position:

• There is adequate space to install any taps or other required

accessories.

• There is adequate space to install the waste pipework and that any

necessary modiﬁcation to internal shelves to accommodate the waste

(and trap) is acceptable.

• Access to any water stop-cock or other services will still be adequate

after the installation.

Installation

• Refer to the cut-out sizes on the back of this manual and use them

to mark out where the worktop needs to be cut. Double-check the

dimensions before cutting the worktop aperture.

• After cutting out the worktop aperture, we recommend you seal the

cut edges with silicone (or similar) sealant to help prevent ingress of

water.

• Position the supplied gasket around

the perimeter of the hole (Fig. 1).

• It is often easier to mount the taps,

waste-ﬁtting and overﬂow onto the sink

prior to ﬁtting the sink to the worktop.

• Ensure that the external edge of the

sink is positioned on the gasket, to Fig. 1

E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the

right to change speciﬁcations without prior notice.

create a barrier to the ingress

of water and other items between sink

and worktop.

• After positioning the sink on the

worktop, position the ﬁxing brackets

as shown in Fig. 2, then tighten their

screws.

• Do not use a power tool to tighten

the screws; by using a hand tool

it is easier to ensure that they are

tightened just enough to clamp down on the worktop and no

more.

• After ﬁxing, remove any excess gasket material with a suitable cutter.

• We recommend a thin bead of silicone sealer is applied around the

perimeter as added protection against water ingress.

• The taps, waste-ﬁtting and overﬂow can now be mounted onto the

sink (if not already done) and fully connected to their respective

services.

• To check the waste for leaks, close the plug/basket of the waste

ﬁtting, open the tap and ﬁll the sink to the level of the overﬂow; turn

o the tap and wait several minutes to verify that the water doesn’t

drain away.

• Empty the sink.

After ﬁtting, ensure that the enclosed “Stainless Steel Sinks Use and

Maintenance” guide is retained for the customer and/or user of the

sink.

Fig. 2

Produktspezifikationen

Marke:	CDA
Kategorie:	Spülbecken
Modell:	KA30SS
Breite:	860 mm
Tiefe:	500 mm
Produktfarbe:	Edelstahl
Einbauraum Höhe:	170 mm
Anzahl der Spülbecken:	1 Becken
Waschbeckenmaterial:	Edelstahl
Abtropfbrett:	Ja
Wasch-/Spülbeckentyp:	Aufsatzwanne
Form des Beckens:	Rechteckig
Abfluss:	Ja
Wasserhahn enthalten:	Nein