Casio Radio Controled WVA-M650TD-1AER Bedienungsanleitung

Casio Armbanduhr Radio Controled WVA-M650TD-1AER

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio Radio Controled WVA-M650TD-1AER (9 Seiten) in der Kategorie Armbanduhr. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/9

Operation Guide 5110

E-1

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar panel of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run

down. Make sure the watch is exposed to light as much

as possible.

• When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

• You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced signiﬁ cantly

if the face is even only partially covered.

Bright Light

Solar panel

E-2

• The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some

watch functions to be disabled. If the battery goes dead, you will have to

re-conﬁ gure watch settings after recharging. To ensure normal watch operation, be

sure to keep it exposed to light as much as possible.

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Battery charges in the light.

Electrical

energy

Solar panel

(Converts light to

electrical power.)

Some or all

functions

disabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Dis-

charge

Battery discharges in the dark.

E-3

• The actual level at which some functions are disabled depends on the watch

model.

• Frequent display illumination can run down the battery quickly and require

charging. The following guidelines give an idea of the charging time required to

recover from a single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window

Approximately about 8 hours exposure to indoor ﬂ uorescent lighting

• Be sure to read “Power Supply” (page E-49) for important information you

need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

• See “Power Saving Function” (page E-66) for more information.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of your

watch or its malfunction.

E-4

About This Manual

• Depending on the model of your watch, display text

appears either as dark ﬁ gures on a light background

or light ﬁ gures on a dark background. All sample

displays in this manual are shown using dark ﬁ gures

on a light background.

• Button operations are indicated using the letters

shown in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

E-5

Contents

General Guide ………………………………………………………………………… E-8

Radio-controlled Atomic Timekeeping ……………………………………………E-10

To specify your Home City ……………………………………………………E-12

To perform manual receive ……………………………………………………E-24

To check the latest signal reception results …………………………………E-26

World Time ………………………………………………………………………………E-29

To view the current time in another time zone ………………………………E-31

To toggle a city code time between Standard Time and

Daylight Saving Time ………………………………………………………E-32

To swap your Home City and World Time City ………………………………E-33

Stopwatch ………………………………………………………………………………E-34

To measure times with the stopwatch ………………………………………E-35

E-6

Countdown Timer………………………………………………………………………E-36

To use the countdown timer ……………………………………………………E-37

To conﬁ gure countdown start time and auto-repeat settings ………………E-38

Alarms ……………………………………………………………………………………E-40

To set an alarm time ……………………………………………………………E-41

To turn an alarm on and off ……………………………………………………E-43

To turn the Hourly Time Signal on and off ……………………………………E-44

Illumination ……………………………………………………………………………E-45

To illuminate the display manually ……………………………………………E-45

To turn the auto light switch on and off ………………………………………E-48

Power Supply …………………………………………………………………………E-49

Timekeeping ……………………………………………………………………………E-57

To set the time and date manually ……………………………………………E-58

To change the Daylight Saving Time (summer time) setting ………………E-63

E-7

Hand Home Position Correction ……………………………………………………E-64

To adjust the home positions …………………………………………………E-64

Reference ………………………………………………………………………………E-66

To recover from the sleep state ………………………………………………E-67

To turn Power Saving on and off ………………………………………………E-68

Speciﬁ cations …………………………………………………………………………E-75

E-8

General Guide

• Press C to change from mode to mode.

• In any mode (except a setting mode), press B to illuminate the display for about

one second.

Timekeeping Mode

Press .&

E-9

Alarm Mode (page E-40)

Stopwatch Mode (page E-34)

Countdown Timer Mode (page E-36)

World Time Mode (page E-29)

Operation Guide 5110

E-10

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

• This watch is designed to pick up the time calibration signals transmitted in

Germany (Mainﬂ ingen), England (Anthorn), the United States (Fort Collins), China

(Shangqiu), and Japan (Fukushima, Fukuoka/Saga).

• See the information under “Signal Reception Troubleshooting” (page E-27) if you

experience problems with time calibration signal reception.

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time calibration

signal. You also can perform a manual procedure to set the time and date, when

necessary.

• The ﬁ rst thing you should do after purchasing this watch is to specify your

Home City (the city where you normally will use the watch). For more

information, see “To specify your Home City” on page E-12.

E-11

• When using the watch outside the areas covered by the time signal transmitters,

you will have to adjust the current time setting manually as required. See “To set the

time and date manually” (page E-58) for more information about manual time

settings.

• The U.S. time calibration signal can be picked up by the watch while in North

America. The term “North America” in this manual refers to the area that consists of

Canada, the continental United States, and Mexico.

• Using this watch in a country covered by a time calibration signal that is different

from the countries it supports may result in incorrect time indication due to local

application of summer time, etc.

E-12

To specify your Home City

1. In the Timekeeping Mode, hold down A for about ﬁ ve

seconds, until the watch beeps twice and the city code

ﬂ ashes on the upper display. This is the setting mode.

2. Press D (east) and

B (west) to select the city code

you want to use as your Home City.

LIS, LON : Lisbon, London

MAD, PAR, ROM, BER, STO : Madrid, Paris, Rome,

Berlin, Stockholm

ATH : Athens

MOW : Moscow

HKG, BJS, TPE : Hong Kong, Beijing, Taipei

SEL, TYO : Seoul, Tokyo

HNL : Honolulu

ANC

: Anchorage

YVR, LAX : Vancouver, Los Angeles

YEA, DEN

: Edmonton, Denver

MEX, CHI : Mexico City, Chicago

Left dial hand

PM indicator Seconds

Hour : Minutes

City code

E-13

MIA, YTO, NYC : Miami, Toronto, New York

YHZ : Halifax

YYT : St.Johns

3. Press A to exit the setting mode.

• Normally, your watch should show the correct time as soon as you select your

Home City code. If it does not, it should adjust automatically after the next auto

receive operation (in the middle of the night). You also can perform manual

receive (page E-24) or you can set the time manually (page E-58).

• The watch will receive the time calibration signal automatically from the

applicable transmitter (in the middle of the night) and update its settings

accordingly. For information about the relationship between city codes and

transmitters, see page E-17 and “Transmitters” (page E-70).

• See the maps under “Approximate Reception Ranges” (page E-18) for

information about the reception ranges of the watch.

E-14

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal:

auto receive and manual receive.

• Auto Receive

With auto receive, the watch receives the time calibration signal automatically up to

six times a day (ﬁ ve times for the Chinese calibration signal). When any auto receive

is successful, remaining auto receive operations are not performed. For more

information, see “About Auto Receive” (page E-21).

• Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a

button. For more information, see “To perform manual receive” (page E-24).

E-15

Important!

• When getting ready to receive the time calibration signal, position the watch as

shown in the nearby illustration, with its 12 o’clock side pointing towards a window.

This watch is designed to receive a time calibration signal late at night. Because of

this, you should place the watch near a window as shown in the illustration when

you take it off at night. Make sure there are no metal objects nearby.

12 o’clock

• Make sure the watch is facing the right way.

E-16

• Proper signal reception can be difﬁ cult or even impossible under the conditions

listed below.

Inside or

among

buildings

Inside a

vehicle

Near household

appliances,

ofﬁ ce

equipment, or a

mobile phone

Near a

construction

site, airport, or

other sources

of electrical

noise

Near high-

tension power

lines

Among or

behind

mountains

• Signal reception normally is better at night than during the day.

• Time calibration signal reception takes from two to seven minutes, but in some

cases it can take as long as 14 minutes. Take care that you do not perform any

button operations or move the watch during this time.

E-17

• The time calibration signal the watch will attempt to pick up depends on its current

Home City code setting as shown below.

Home City Code Transmitter Frequency

LON, PAR, BER, ATH,

LIS, MAD, ROM, STO, MOW*

Anthorn (England) 60.0 kHz

Mainﬂ ingen (Germany) 77.5 kHz

HKG, BJS Shangqiu City (China) 68.5 kHz

TPE, SEL, TYO Fukushima (Japan) 40.0 kHz

Fukuoka/Saga (Japan) 60.0 kHz

HNL*, ANC*, LAX, DEN,

CHI, NYC, YVR, YEA, MEX,

MIA, YTO, YHZ, YYT

Fort Collins, Colorado

(the United States) 60.0 kHz

* The areas covered by the

HNL,ANC, and MOW city codes are quite far from the

time calibration signal transmitters, and so certain conditions may cause

problems with signal reception.

• Calibration signal reception is disabled while a countdown timer operation is in

progress.

E-18

Approximate Reception Ranges

U.S. Signal

600 miles

(1,000 kilometers)

Fort Collins

2,000 miles

(3,000 kilometers)

1,500 kilometers

UK and German Signals

Mainflingen

Anthorn

500 kilometers

The Anthorn signal is

receivable within this

area.

E-19

500 kilometers 500 kilometers

Fukushima

1,000 kilometers

Fukuoka/Saga

1,000 kilometers

Japanese Signals

Signals are receivable in the Taiwan area when reception conditions are good.

Changchun

Beijing

Shanghai

Hong Kong

1,500 kilometers

500 kilometers

Chengdu

Shangqiu

Chinese Signal

Operation Guide 5110

E-20

• Signal reception may not be possible at the distances that are further than those

noted below during certain times of the year or day. Radio interference also may

cause problems with reception.

Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers

(310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 500 kilometers (310 miles)

• Even when the watch is within the reception range of the transmitter, signal

reception will be impossible if the signal is blocked by mountains or other

geological formations between the watch and signal source.

• Signal reception is affected by weather, atmospheric conditions, and seasonal

changes.

• As of December 2013, China does not use Daylight Saving Time (DST). If China

does go to the Daylight Saving Time system in the future, some functions of this

watch may no longer operate correctly.

E-21

About Auto Receive

The watch receives the time calibration signal automatically up to six times a day (ﬁ ve

times for the Chinese calibration signal). When any auto receive is successful,

remaining auto receive operations are not performed. The reception schedule

(calibration times) depends on your currently selected Home City, and whether

standard time or Daylight Saving Time is selected for your Home City.

Your Home City Auto Receive Start Times

1 2 3 4 5 6

LON

LIS

Standard Time

Daylight Saving Time

1:00 am

2:00 am

3:00 am

4:00 am

5:00 am

Midnight

1:00 am*

PAR

BER

MAD

ROM

STO

Standard Time

Daylight Saving Time

2:00 am

3:00 am

4:00 am

5:00 am

Midnight

1:00 am*

2:00 am*

ATH Standard Time

Daylight Saving Time

3:00 am

4:00 am

5:00 am

Midnight

1:00 am*

2:00 am*

3:00 am*

MOW Standard Time

Daylight Saving Time

4:00 am

5:00 am

Midnight

1:00 am*

2:00 am*

3:00 am*

4:00 am*

E-22

Your Home City Auto Receive Start Times

1 2 3 4 5 6

HKG

BJS

Standard Time 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

TYO

TPE

SEL

Standard Time Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

HNL

ANC

LAX

DEN

CHI

NYC

YVR

YEA

MEX

MIA

YTO

YHZ

YYT

Standard Time and

Daylight Saving Time

Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

*Next day E-23

Note

• When a calibration time is reached, the watch will receive the calibration signal only

if it is in either the Timekeeping Mode or World Time Mode. Reception is not

performed if a calibration time is reached while you are conﬁ guring settings.

• Auto receive of the calibration signal is designed to be performed early in the

morning, while you sleep (provided that the Timekeeping Mode time is set

correctly). Before going to bed for the night, remove the watch from your wrist, and

put it in a location where it can receive the signal easily.

• The watch receives the calibration signal for two to 14 minutes everyday when the

time in the Timekeeping Mode reaches a calibration time. Do not perform any

button operation within 14 minutes before or after the calibration times. Doing so

can interfere with correct calibration.

• Remember that reception of the calibration signal depends on the current time in

your Home City, as kept in the Timekeeping Mode.

E-24

To perform manual receive

Place the watch on a stable surface so its 12 o’clock

side is facing towards a window (page E-15).

2. In the Timekeeping Mode, hold down A for about two

seconds until the watch beeps.

3. The digital display will go blank, and the left dial hand

will move to R

( READY). This indicates that the watch

is getting ready for time calibration signal reception.

• See the information under “Signal Reception

Troubleshooting” (page E-27) if you experience

problems.

• The left dial hand will move to W (WORK) and stay

there while actual reception is in progress.

• If signal reception is unstable during reception, the left

dial hand may move between W (WORK) and

R (READY).

• The hour and minute hands continue to keep time

normally.

W (WORK)

R (READY)

Receiving

E-25

• Time calibration signal reception takes from two to

seven minutes, but in some cases it can take as long

as 14 minutes. Take care that you do not perform any

button operations or move the watch during this time.

• When a signal receive operation is successful,

GET

appears on the upper display and the lower display

shows the time and date of the successful operation.

The watch will adjust its time setting in accordance

with the information provided by the signal.

• The watch will return to the Timekeeping Mode if you

press A or if you do not perform any operation for

about one or two minutes.

•ERR will appear on the upper display if the receive

operation is not successful. The watch will not adjust

its time setting in this case. Press A to return to the

Timekeeping Mode.

Receive successful

Receive failed

E-26

Note

• To interrupt a receive operation and return to the Timekeeping Mode, press any

button.

To check the latest signal reception results

In the Timekeeping Mode, press

A to view the last successful receive time and date.

Press A again to return to the previous screen.

Date Hour : Minutes

E-27

Signal Reception Troubleshooting

Check the following points whenever you experience problems with signal reception.

Problem Probable Cause What you should do

I can’t receive

a time

calibration

signal.

• You performed some button

operation during auto receive.

• The watch is not in the Timekeeping

Mode or World Time Mode.

• The watch is in a location where the

signal cannot be received for some

reason.

• A countdown timer operation is in

progress.

• Radio interference is often present

during the day time, which can

interfere with signal reception.

• Perform manual receive at night or

wait until the next auto receive

operation is performed.

• Enter the Timekeeping Mode or

World Time Mode and try again.

• Enter the Countdown Timer Mode

and stop the countdown. (page

E-36)

• Check to make sure the watch is in

a location where it can receive the

signal (page E-15).

E-28

Problem Probable Cause What you should do

The time

setting is

incorrect

following

signal

reception.

• If the time is one hour off, the DST

setting may be incorrect.

• The Home City code setting is not

correct for the area where you are

using the watch.

• The home positions of the hands are

off.

• Change the DST setting to Auto DST

(page E-63).

• Select the correct Home City code

(page E-12).

• Enter the home position adjustment

mode and adjust the home

positions (page E-64).

• For further information, see “Important!” (page E-15) and “Radio-controlled Atomic

Timekeeping Precautions” (page E-69).

E-29

World Time

World Time digitally displays the current time in one of

48 cities (29 time zones) around the world. A simple

operation swaps your Home City with the currently

selected World Time City.

• When you enter the World Time Mode, the current

month and day of the World Time City appear ﬁ rst.

After about one second, the current time appears.

• The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

Current time in

World Time City

Currently selected

World Time City

Produktspezifikationen

Marke:	Casio
Kategorie:	Armbanduhr
Modell:	Radio Controled WVA-M650TD-1AER

Brauchst du Hilfe?

Wenn Sie Hilfe mit Casio Radio Controled WVA-M650TD-1AER benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Armbanduhr Casio

Casio Vintage A100WEL-1A Bedienungsanleitung

25 Juni 2024

Casio Vintage A158WA-1J Bedienungsanleitung

25 Juni 2024

Casio Vintage A100WEF Bedienungsanleitung

25 Juni 2024

Casio Vintage A159WA-N1 Bedienungsanleitung

25 Juni 2024

Casio Vintage A120WE-1A Bedienungsanleitung

25 Juni 2024

Casio Vintage A158WEA-9 Bedienungsanleitung

25 Juni 2024

Casio Vintage A100WEPC-1B Bedienungsanleitung

25 Juni 2024

Casio Edifice EFB-508 Bedienungsanleitung

20 Juni 2024

Casio vEdifice EFV-C110 Bedienungsanleitung

2 Juni 2024

Casio G-Shock GMA-S130 Bedienungsanleitung

2 Juni 2024

Bedienungsanleitung Armbanduhr

Neueste Bedienungsanleitung für -Kategorien-

Zenith Defy El Primero 21 18.9000.9004/71.R585 Bedienungsanleitung

19 August 2024

Zenith Elite Classic 03.2290.679/51.C700 Bedienungsanleitung

19 August 2024

Invicta Character Collection 24492 Bedienungsanleitung

16 August 2024

Lorus Sports RRX43FX9 Bedienungsanleitung

12 August 2024

Invicta Objet D Art 27572 Bedienungsanleitung

10 August 2024

Invicta Objet D Art 27560 Bedienungsanleitung

9 August 2024

Digi-tech 1-LD2580 Bedienungsanleitung

11 Juni 2024

Digi-tech 1-LD2550 Bedienungsanleitung

11 Juni 2024

Digi-tech 1-LD2339 Bedienungsanleitung

11 Juni 2024

Digi-tech 1-LD2900 Bedienungsanleitung

11 Juni 2024