Casio G9000-1V Bedienungsanleitung

Casio betrachten G9000-1V

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio G9000-1V (4 Seiten) in der Kategorie betrachten. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
1
Operation Guide 3031
To measure times with the stopwatch
(Stopwatch Mode (ST1) and Stopwatch Mode (ST2))
Elapsed Time
Start Stop Re-start Stop Clear
Start Split
( displayed)
Split release Stop Clear
Start Split Stop Split release Clear
Split Time
Two Finishes
First runner finishes.
Display time of first
runner.
Second runner
finishes.
Display time of
second runner.
About Auto-Start (Stopwatch Mode (ST1))
With Auto-Start, the watch performs a 5-second countdown, and stopwatch operation
starts automatically when the countdown reaches zero.
During the final three seconds of the countdown, a beeper sounds with each second.
To use Auto-Start (ST1)
1. While the stopwatch screen is showing all zeros in the
Stopwatch Mode, press B.
•This displays a 5-second countdown screen.
•To return to the all zeros screen, press B again.
2. Press D to start the countdown.
•When the countdown reaches zero, a tone sounds and
a stopwatch timing operation starts automatically.
•Pressing D while the Auto-Start countdown is in
progress starts the stopwatch immediately.
Stopwatches
Your watch has two stopwatch modes:Stopwatch Mode
(ST1) and Stopwatch Mode (ST2). Both stopwatch modes
let you measure elapsed time, split times, and two
finishes. The Stopwatch Mode (ST1) includes Auto-Start.
•A display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds.
•A stopwatch continues to run, restarting from zero after
it reaches its limit, until you stop it.
•A stopwatch measurement operation continues even if
you exit a Stopwatch Mode.
•Exiting a Stopwatch Mode while a split time is frozen on
the display clears the split time and returns to elapsed
time measurement.
•All of the operations in this section are performed in the
Stopwatch Mode (ST1) or Stopwatch Mode (ST2),
which you enter by pressing C.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press to toggle between 12-hour timekeeping and 24-D
hour timekeeping.
•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
•The P indicator is not displayed when the current time is displayed in other modes.
MA0604-EA
About This Manual
•Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
•Button operations are indicated using the letters shown
in the illustration.
•Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Timekeeping Mode World Time ModeAlarm ModeCountdown Timer ModeStopwatch Mode (ST1) Stopwatch Mode (ST2)
Press .
General Guide
•Press C to change from mode to mode.
•In any mode, press L to illuminate the display.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds Home Time Zone Hour
Year MinutesDay
DST
Month
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Home time zone
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
Read This Before You Set the Time and Date !
The times displayed in the Timekeeping Mode and World
Time Mode are linked. Because of this, make sure you
select a Home Time zone before you set the time and
date.
Day of week
Month – Day
Hour : Minutes
PM indicator
Seconds
DST indicator
Screen
50
OFF
6-30
To do this:
Reset the seconds to 00
Toggle between Daylight Saving
Time (ON) and Standard Time (
OFF)
Specify your Home Time zone
Change the hour or minutes
Change the year
Change the month or day
Do this:
Press .D
Press .D
Use D (eastward) and B (westward).
Use ).D (+) and B (–
•
For details about time zones, see the
“
City Code Table
”
.
•See “Daylight Saving Time (DST) for details about DST setting.”
4. Press A to exit the setting screen.
•The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time
(ON displayed) and Standard Time (OFF displayed).
4. Press A to exit the setting screen.
•The DST indicator appears on the display to indicate
that Daylight Saving Time is turned on.
1/100 second
Minutes
Seconds
Timekeeping Mode time
*During stopwatch elapsed
time measurement,
shows the number of
hours elapsed.
2
Operation Guide 3031
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (SIG).
2. Press A to toggle it on and off.
•The Hourly Time Signal on indicator ( ) is shown on
the display in all modes while this function is turned on.
5. Press A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
•Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
•To stop the alarm tone after it starts to sound, press any button.
•Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ
setting screen
To test the alarm
In the Alarm Mode, hold down to sound the alarm.D
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
•Turning on a alarm (SNZ, AL1, , AL2 AL3, or
AL4) displays the alarm on indicator ( , , , ,
or ).
•In all modes, the alarm on indicator is shown for alarm
that is currently turned on.
•The alarm on indicator flashes while the alarm is
sounding.
•The snooze alarm indicator ( ) flashes while the
snooze alarm is sounding and during the 5-minute intervals
between alarms.
Alarms
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
•There are five alarm screens numbered AL1, AL2,
AL3 AL4, and for the one-time alarm, a snooze
alarm screen indicated by SNZ. The Hourly Time
Signal screen is indicated by SIG.
•All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
•To specify a countdown start time of 24 hours, set .
4. Press A to exit the setting screen.
•You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press while in the Countdown Timer Mode to start theD
countdown timer.
•The countdown timer operation continues even if you
exit the Countdown Timer Mode.
•Press D while a countdown operation is in progress to
pause it. Press again to resume the countdown.D
•To stop a countdown operation completely, first pause it
(by pressing ), and then press . This returns theD B
countdown time to its starting value.
Countdown Timer
The countdown timer can be set within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero. The countdown timer also has an auto-
repeat feature and a progress beeper that signals the
progress of the countdown.
•All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
•See “To configure the countdown timer for information”
about setting up the timer.
Seconds
Hours
Minutes
Setting
Hours, Minutes
Auto-repeat
Progress Beeper
Screen Button Operation
Use D (+) and B (–) to change the setting.
Press D to toggle auto-repeat on ( displayed) and off
( displayed).
Press ).D to toggle the progress beeper on ( ) and off (
Alarm time
(Hour : Minutes)
Alarm number
Alarm on indicator
Alarm date
(Month – Day)
Alarm Types
The alarm type is determined by the settings you make, as described below.
••
••
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
••
••
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
••
••
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
••
••
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D or B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
•To set a one-time alarm, display an alarm screen AL1, , .AL2 AL3, or AL4
To set the snooze alarm, display the SNZ screen.
•The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
•This operation turns on the alarm automatically.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour Minutes Month Day
4. While a setting is flashing, use D and B to change it as described below.
Screen To do this:
Change the hour
and minutes
Change the
month and day
Do this:
Use ).D (+) and B (–
•With the 12-hour format, set the time correctly as a.m.
or p.m. (P indicator).
•To set an alarm that does not include a month and/or
day, set for each setting.
Snooze alarm
indicator
Hourly time signal
on indicator
Auto-repeat
When auto-repeat is turned on, the countdown restarts automatically from the
countdown start time when it reaches zero.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
•Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing , or you canD
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
•When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
•When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
•Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
•30 seconds before the end of the countdown, the watch emits four short beeps.
•The watch emits a short beep for each of the last 10 seconds of the countdown.
•If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down until the currentA
countdown start time starts to flash, which indicates the
setting screen.
•If the countdown start time is not displayed, use the
procedure under To use the countdown timer“ ” to
display it.
2. Press to move the flashing in the sequence shownC
below to select other settings.
Hours
Progress Beeper
Minutes
Auto-repeat
3. When the setting you want to change is flashing, use B and D to change it as
described below.
3
Operation Guide 3031
Button Operation Tone
The button operation tone sounds any time you press one
of the watch s buttons. You can turn the button operation’
tone on or off as desired.
•Even if you turn off the button operation tone, the
alarms, the Hourly Time Signal, the countdown alarm,
and stopwatch auto start all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down to toggle the button operation toneC
on ( not displayed) and off ( displayed).MUTE MUTE
•Holding down C to turn the button operation tone on or off also causes the watch’s
current mode to change.
•The MUTE indicator is displayed in all modes when the button operation tone is
turned off.
Auto Return Features
•If you leave the watch in the Alarm Mode for two or three minutes without performing
any operation, it automatically changes to the Timekeeping Mode.
•If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Timekeeping
•Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
•The year can be set in the range of 2000 to 2099.
•The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch s battery replaced.’
World Time
All World Time Mode times are calculated from the current Home City time in the
Timekeeping Mode using UTC time differential values.
•The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
•The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
•The letters “ ” “UTC is the abbreviation for Coordinated Universal Time , which is the”
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.
Flash Alert
When Flash Alert is turned on, the illumination flashes for
the alarms, the Hourly Time Signal, the countdown alarm,
and stopwatch (ST1) auto start.
To turn Flash Alert on and off
In the Timekeeping Mode, hold down for about threeD
seconds to toggle Flash Alert on (Flash Alert indicator
displayed) or off (Flash Alert indicator not displayed).
•Illumination flashes twice when you turn Flash Alert on
and once when turn Flash Alert off.
•While Flash Alert is turned on, the Flash Alert indicator
remains on the display in all modes.
•Note that pressing D to toggle Flash Alert on or off will
also switch timekeeping between 12-hour and 24-hour
format.
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Warning!
•Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not startle or distract others
around you.
•When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down for about three seconds to toggle the autoB
light switch on (auto light switch indicator displayed) or off (auto light switch indicator
not displayed).
•The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
•In order to protect against running down the battery, the auto light switch turns off
automatically approximately six hours after you turn it on.
To illuminate the display
In any mode, press to turn on illumination.L
•The above operation turns on illumination regardless of the current auto light switch
setting.
•You can use the procedure below to select either 3 seconds or 5 seconds as the
illumination duration. When you press , the illumination will remain on for aboutL
3 seconds or 5 seconds, depending on the current illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down until theA
seconds start to flash, which indicates the setting
screen.
2. While the seconds are flashing, press to toggle theB
setting between 3 seconds ( ) and 5 seconds ( ).
3. Press to exit the setting screen.A
Illumination
This watch has two EL (electro-luminescent) panels that
cause the entire display to glow for easy reading in the
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch for reading
towards your face.
•The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
•See “Illumination Precautions” for more important
information.
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world.
•All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time for another city code
In the World Time Mode, press to scroll eastwardlyD
through city codes.
In the World Time Mode, press B to scroll westwardly
through city codes.
•For full information about city codes, see the “City Code
Table”.
•If the current time for a city is wrong, check your
Timekeeping Mode time and time zone settings and
make necessary changes.
Current time and date in
the zone of the selected
city code
City code
Auto light switch indicator
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D B (east) and (west) to
display the city code (time zone) whose Standard Time/
Daylight Saving Time setting you want to change.
2. Hold down A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
•The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
•Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
DST indicator
Parallel to ground More than 40
°
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Areas
There are three graphic areas named A, B, and C. The information shown in each
graphic area depends on the current mode.
Graphic area B
Graphic area A
Graphic area C
•The following table shows the information that appears in graphic area A.
Flash Alert indicator
•In all modes, graphic area B shows the Stopwatch Mode (ST1) minutes (one
segment each for 5 minutes, 10 minutes, etc.).
•In all modes, graphic area C shows the Stopwatch Mode (ST2) minutes (one
segment each for 5 minutes, 10 minutes, etc.).
Mode
Timekeeping
World Time
Stopwatch (ST1 and ST2)
Countdown Timer
Alarm
Graphic Area A
Timekeeping Mode seconds
Timekeeping Mode seconds
Sweeps from left to right
Sweeps from right to left
No indication

Produktspezifikationen

Marke: Casio
Kategorie: betrachten
Modell: G9000-1V

Brauchst du Hilfe?

Wenn Sie Hilfe mit Casio G9000-1V benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung betrachten Casio

Casio

Casio GW-3000BD-1AER Bedienungsanleitung

9 Oktober 2024
Casio

Casio Edifice EFA-112D-1AVEF Bedienungsanleitung

7 Oktober 2024
Casio

Casio Baby-G BGA-200-1E2ER Bedienungsanleitung

6 Oktober 2024
Casio

Casio MTP-1302D-7A1VEF Bedienungsanleitung

1 Oktober 2024
Casio

Casio Baby-G BG-5600WH-7ER Bedienungsanleitung

30 September 2024
Casio

Casio Edifice EF-316D-1AVEF Bedienungsanleitung

25 September 2024
Casio

Casio GW-A1100-1A3ER Bedienungsanleitung

23 September 2024
Casio

Casio G-Shock GMA-B800 Bedienungsanleitung

21 September 2024
Casio

Casio DW-5600E-1VER Bedienungsanleitung

20 September 2024
Casio

Casio LW-S200H-8AEF Bedienungsanleitung

16 September 2024

Bedienungsanleitung betrachten

Neueste Bedienungsanleitung für -Kategorien-

Citizen

Citizen Cal 411X Bedienungsanleitung

7 Oktober 2024
Jaguar

Jaguar J627 Bedienungsanleitung

6 Oktober 2024
Citizen

Citizen CAL 4633 Bedienungsanleitung

5 Oktober 2024
Auriol

Auriol IAN 277495 Bedienungsanleitung

4 Oktober 2024
La Crosse Technology

La Crosse Technology WT-941 Bedienungsanleitung

4 Oktober 2024
Spin Master

Spin Master Dumas SP-5081-11 Bedienungsanleitung

4 Oktober 2024
Michael Kors

Michael Kors Kors Access Scout Hutton MKT4024 Bedienungsanleitung

3 Oktober 2024
Auriol

Auriol IAN 43022 Bedienungsanleitung

2 Oktober 2024
Michael Kors

Michael Kors Kors Access Sofie MKT5039 Bedienungsanleitung

2 Oktober 2024
Citizen

Citizen CAL 5513 Bedienungsanleitung

1 Oktober 2024