Casio G-Shock GW-M500 Bedienungsanleitung

Casio betrachten G-Shock GW-M500

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Casio G-Shock GW-M500 (9 Seiten) in der Kategorie betrachten. Dieser Bedienungsanleitung war fĂĽr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/9
Operation Guide 3405
MO1206-EA © 2012 CASIO COMPUTER CO., LTD.
E-1
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Keep the watch exposed to bright light
The electricity generated by the solar panel of the watch is
stored by a rechargeable battery. Leaving or using the
watch where it is not exposed to light causes the battery
to run down. Make sure the watch is exposed to light as
much as possible.
•When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
•You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is covered only partially.
l
l
l
l
l
l
l
l
l
l
l
Bright Light
Solar panel
E-2
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Rechargeable battery
Bright Light
Electrical
energy
Solar panel
(Converts light to
electrical power.)
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some or all
functions
disabled
Dis-
charge
Battery charges in the light. Battery discharges in the dark.
•The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
E-3
•The actual level at which some functions are disabled depends on the watch model.
•Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately about 8 hours exposure to indoor fluorescent lighting
•Be sure to read “Power Supply” (page E-50) for important information you
need to know when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
•See “Power Saving Function” (page E-67) for more information.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
or loss suffered by you or any third party arising through the use of this product or
its malfunction.
E-4
About This Manual
•Depending on the model of your watch, display text appears either as dark figures
on a light background or light figures on a dark background. All sample displays in
this manual are shown using dark figures on a light background.
•Button operations are indicated using the letters shown in the illustration.
•Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
E-5
Contents
General Guide ......................................................................................................... E-8
Radio-controlled Atomic Timekeeping ............................................................... E-10
World Time ............................................................................................................. E-33
Alarms .................................................................................................................... E-36
Stopwatch .............................................................................................................. E-41
Countdown Timer .................................................................................................. E-43
Illumination ............................................................................................................ E-46
Power Supply ........................................................................................................ E-50
Timekeeping .......................................................................................................... E-58
Reference .............................................................................................................. E-65
Specifications ....................................................................................................... E-75
E-6
Procedure Lookup
The following is a handy reference list of all the operational procedures contained in
this manual.
To specify your Home City ................................................................................... E-12
To perform manual receive .................................................................................. E-26
To turn auto receive on and off ........................................................................... E-28
To check the latest signal reception results ...................................................... E-29
To view the time in another city ........................................................................... E-34
To toggle a city code time between Standard Time and
Daylight Saving Time ...................................................................................... E-35
To set an alarm time ............................................................................................. E-37
To test the alarm ................................................................................................... E-38
To turn an alarm on and off .................................................................................. E-39
E-7
To turn the Hourly Time Signal on and off .......................................................... E-40
To measure times with the stopwatch ................................................................ E-42
To configure the countdown timer ...................................................................... E-44
To use the countdown timer ................................................................................ E-45
To illuminate the display manually ...................................................................... E-47
To specify the illumination duration ................................................................... E-47
To turn the auto light switch on and off .............................................................. E-49
To set the time and date manually ...................................................................... E-59
To change the Daylight Saving Time (summer time) setting ............................ E-63
To turn the button operation tone on and off ..................................................... E-66
To recover from the sleep state ........................................................................... E-68
To turn Power Saving on and off ......................................................................... E-68
E-8
General Guide
•Press C to change from mode to mode.
•In any mode (except when a setting screen is on the display), press L to illuminate
the display.
Timekeeping Mode
C
â–˛
C
E-9
Countdown Timer Mode Stopwatch Mode
Alarm Mode
â–˛
World Time Mode
â–˛
C
â–˛
C
C
â–˛
C
C
Operation Guide 3405
E-10
Radio-controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly.
•This watch is designed to pick up the time calibration signals transmitted in Germany
(Mainflingen), England (Anthorn), the United States (Fort Collins), China (Shangqiu),
and Japan (Fukushima, Fukuoka/Saga).
Current Time Setting
This watch adjusts its time setting automatically in accordance with a time calibration
signal. You also can perform a manual procedure to set the time and date, when
necessary.
•The first thing you should do after purchasing this watch is to specify your
Home City (the city where you normally will use the watch). For more
information, see “To specify your Home City” (page E-12).
•When using the watch outside the areas covered by the time signal transmitters, you
will have to adjust the current time setting manually as required. See “Timekeeping”
(page E-58) for more information about manual time settings.
E-11
•The U.S. time calibration signal can be picked up by the watch while in North
America. The term “North America” in this manual refers to the area that consists of
Canada, the continental United States, and Mexico.
•As of June 2012, China does not use Daylight Saving Time (DST). If China does go
to the Daylight Saving Time system in the future, some functions of this watch may
no longer operate correctly.
•Using this watch in a country covered by a time calibration that is different from the
countries it supports may result in incorrect time indication due to local application of
summer time, etc.
E-12
To specify your Home City
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press D B (east) and (west) to select the city code
you want to use as your Home City.
LIS, LON : Lisbon, London
MAD,PAR,ROM,BER STO , : Madrid, Paris,
Rome, Berlin, Stockholm
ATH : Athens
MOW : Moscow
HKG BJS, , TPE : Hong Kong, Beijing, Taipei
SEL,TYO : Seoul, Tokyo
HNL : Honolulu
ANC : Anchorage
YVR,LAX: Vancouver, Los Angeles
YEA DEN, : Edmonton, Denver
MEX,CHI : Mexico City, Chicago
NYC : New York
YHZ : Halifax
YYT : St.Johns
City code
PM indicator
SecondsHour : Minutes
E-13
3. Press A to exit the setting screen.
•Normally, your watch should show the correct time as soon as you select your Home
City code. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night). You also can perform manual receive (page
E-26) or you can set the time manually (page E-59).
•The watch will receive the time calibration signal automatically from the applicable
transmitter (in the middle of the night) and update its settings accordingly. For
information about the relationship between city codes and transmitters, see page
E-17 and “Transmitters” (page E-70).
•See the maps under “Approximate Reception Ranges” (page E-18) for information
about the reception ranges of the watch.
•You can disable time signal reception, if you want. See “To turn auto receive on and
off” on page E-28 for more information.
•Under factory default settings, auto receive is turned off for all of the following city
codes: MOW (Moscow), HNL (Honolulu), and (Anchorage). For details aboutANC
turning on auto receive for these city codes, see “To turn auto receive on and off” on
page E-28.
E-14
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
•Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to
six times a day (five times a day for the Chinese calibration signal). When any auto
receive is successful, the remaining auto receive operations are not performed. For
more information, see “About Auto Receive” (page E-21).
•Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive” (page E-26).
E-15
Important!
•When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side pointing towards a window.
This watch is designed to receive a time calibration signal late at night. Because of
this, you should place the watch near a window as shown in the illustration when you
take it off at night. Make sure there are no metal objects nearby.
12 o’clock
or
•Make sure the watch is facing the right way.
E-16
•Proper signal reception can be difficult or even impossible under the conditions listed
below.
Inside or
among
buildings
Inside a
vehicle Near a
construction
site, airport,
or other
sources of
electrical
noise
Near high-
tension power
lines
Near
household
appliances,
office
equipment,
or a mobile
phone
Among or
behind
mountains
•Signal reception normally is better at night than during the day.
•Time calibration signal reception takes from two to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
E-17
•The time calibration signal the watch will attempt to pick up depends on its current
Home City code setting as shown below.
Home City Code
LIS, LON, MAD, PAR, ROM,
BER, STO, ATH, MOW*
HKG, BJS
TPE, SEL, TYO
HNL*, ANC*, YVR, LAX, YEA,
DEN, MEX, CHI, NYC, YHZ, YYT
Frequency
60.0 kHz
77.5 kHz
68.5 kHz
40.0 kHz
60.0 kHz
60.0 kHz
Transmitter
Anthorn (England)
Mainflingen (Germany)
Shangqiu City (China)
Fukushima (Japan)
Fukuoka/Saga (Japan)
Fort Collins, Colorado
(the United States)
* The areas covered by the HNL, ANC, and MOW city codes are quite far from the
time calibration signal transmitters, and so certain conditions may cause problems
with signal reception.
•Calibration signal reception is disabled while a countdown timer operation is in
progress.
E-18
Approximate Reception Ranges
U.K. and German Signals
Anthorn
Mainflingen
1,500 kilometers
500 kilometers
The Anthorn signal
is receivable within
this area.
U.S. Signal
Fort Collins
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
E-19
Signals are receivable in the Taiwan area when reception conditions are good.
Shangqiu
1,000 kilometers
1,000 kilometers
Fukuoka/Saga
500 kilometers
Fukushima
500 kilometers
500 kilometers
Changchun
Beijing
1,500 kilometers
Shanghai
Chengdu
Japan Signals
China Signal
Hong Kong
Operation Guide 3405
E-20
•Signal reception may not be possible at the distances noted below during certain
times of the year or day. Radio interference also may cause problems with reception.
Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers
(310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 500 kilometers (310 miles)
•Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
•Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
•See the information under “Signal Reception Troubleshooting” (page E-30) if you
experience problems with time calibration signal reception.
E-21
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day
(five times a day for the Chinese calibration signal). When any auto receive is
successful, the remaining auto receive operations are not performed. The reception
schedule (calibration times) depends on your currently selected Home City, and
whether standard time or Daylight Saving Time is selected for your Home City.
2:00 am
3:00 am
3:00 am
4:00 am
4:00 am
5:00 am
5:00 am
Midnight*
3:00 am
4:00 am
4:00 am
5:00 am
5:00 am
Midnight*
Midnight*
1:00 am*
4:00 am
5:00 am
5:00 am
Midnight*
Midnight*
1:00 am*
1:00 am*
2:00 am*
5:00 am
Midnight*
Midnight*
1:00 am*
1:00 am*
2:00 am*
2:00 am*
3:00 am*
Standard Time
Daylight Saving Time
Standard Time
Daylight Saving Time
Standard Time
Daylight Saving Time
Standard Time
Daylight Saving Time
1:00 am
2:00 am
2:00 am
3:00 am
3:00 am
4:00 am
4:00 am
5:00 am
Midnight*
1:00 am*
1:00 am*
2:00 am*
2:00 am*
3:00 am*
3:00 am*
4:00 am*
LIS
LON
MAD
PAR
ROM
BER
STO
ATH
MOW
Your Home City Auto Receive Start Times
1 2 3 4 5 6
E-22
*Next day
HKG
BJS
TPE
SEL
TYO
HNL
ANC
YVR
LAX
YEA
DEN
MEX
CHI
NYC
YHZ
YYT
Your Home City Auto Receive Start Times
1 2 3 4 5 6
Standard Time and
Daylight Saving Time
Standard Time
Standard Time and
Daylight Saving Time
1:00 am
Midnight
Midnight
2:00 am
1:00 am
1:00 am
3:00 am
2:00 am
2:00 am
4:00 am
3:00 am
3:00 am
5:00 am
4:00 am
4:00 am
5:00 am
5:00 am
E-23
Note
•When a calibration time is reached, the watch will receive the calibration signal only
if it is in either the Timekeeping Mode or World Time Mode. Reception is not
performed if a calibration time is reached while you are configuring settings.
•Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
•The watch receives the calibration signal for two to seven minutes everyday when
the time in the Timekeeping Mode reaches a calibration time. Do not perform any
button operation within seven minutes before or after the calibration times. Doing so
can interfere with correct calibration.
•Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the displayed
time actually is the correct time.
E-24
About the Signal Strength Indicator
The signal strength indicator shows the strength of the calibration signal being
received. For best reception, be sure to keep the watch in a location where signal
strength is strongest. The signal strength indicator is displayed while an auto or
manual receive operation is in progress.
Receiving indicator
Signal strength indicator
Strong
(Level 3)
Weak
(Level 1)
•Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the signal strength indicator to indicate signal
strength.
E-25
•Use the signal strength indicator as a guide for checking signal strength and for
finding the best location for the watch dur ing signal receive operations.
•Following reception of the time calibration signal and calibration of the watch’s time
setting, the receiving indicator will remain on the display in all modes. The receiving
indicator will not be displayed if signal reception was unsuccessful or after you adjust
the current time setting manually.
•The receiving indicator is displayed only when the watch is able to receive both time
and date data successfully. It does not appear when only time data is received.
•The receiving indicator indicates that at least one of the auto calibration signal
receive operations was successful. Note, however, that the receiving indicator
disappears from the display each day when the first auto receive operation of the
day is performed.
E-26
To perform manual receive
1. Enter the Timekeeping Mode (page E-8).
2. Hold down D for about two seconds until the receiving
indicator starts to flash on the display. This indicates
that manual receive is in progress.
•Time calibration signal reception takes from two to
seven minutes. Take care that you do not perform
any button operations or move the watch during this
time.
•If the receive operation is successful, the reception
date and time appear on the display, along with the
GET indicator.
3. After manual receive is complete, press D to return to
normal timekeeping.
•The watch also will return to normal timekeeping if you
do not perform any button operation for about one or
two minutes.
Receiving
Receive successful
E-27
•If the latest reception fails but a previous reception was
successful, the receiving indicator will be on the display.
Note
•To interrupt a receive operation and return to normal
timekeeping, press D.
If there was a previously
successful reception
If no reception was
successful
Receive failed
E-28
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the last
successful receive time and date screen (page E-29).
2. Hold down A until the current auto receive setting (ON
or OFF) starts to flash. This is the setting screen.
•Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on (ON) and off
(OFF).
4. Press A to exit the setting screen.
•For information about city codes that support signal
receive, see “To specify your Home City” (page E-12).
On/Off status
E-29
To check the latest signal reception results
In the Timekeeping Mode, press D to view the last
successful receive time and date. Press again toD
return to the previous screen.
•The watch also will return to normal timekeeping if you
do not perform any button operation for about one or two
minutes.

Produktspezifikationen

Marke: Casio
Kategorie: betrachten
Modell: G-Shock GW-M500

Brauchst du Hilfe?

Wenn Sie Hilfe mit Casio G-Shock GW-M500 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung betrachten Casio

Casio

Casio GW-3000BD-1AER Bedienungsanleitung

9 Oktober 2024
Casio

Casio Edifice EFA-112D-1AVEF Bedienungsanleitung

7 Oktober 2024
Casio

Casio Baby-G BGA-200-1E2ER Bedienungsanleitung

6 Oktober 2024
Casio

Casio MTP-1302D-7A1VEF Bedienungsanleitung

1 Oktober 2024
Casio

Casio Baby-G BG-5600WH-7ER Bedienungsanleitung

30 September 2024
Casio

Casio Edifice EF-316D-1AVEF Bedienungsanleitung

25 September 2024
Casio

Casio GW-A1100-1A3ER Bedienungsanleitung

23 September 2024
Casio

Casio G-Shock GMA-B800 Bedienungsanleitung

21 September 2024
Casio

Casio DW-5600E-1VER Bedienungsanleitung

20 September 2024
Casio

Casio LW-S200H-8AEF Bedienungsanleitung

16 September 2024

Bedienungsanleitung betrachten

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Citizen

Citizen Cal 411X Bedienungsanleitung

7 Oktober 2024
Jaguar

Jaguar J627 Bedienungsanleitung

6 Oktober 2024
Citizen

Citizen CAL 4633 Bedienungsanleitung

5 Oktober 2024
Auriol

Auriol IAN 277495 Bedienungsanleitung

4 Oktober 2024
La Crosse Technology

La Crosse Technology WT-941 Bedienungsanleitung

4 Oktober 2024
Spin Master

Spin Master Dumas SP-5081-11 Bedienungsanleitung

4 Oktober 2024
Michael Kors

Michael Kors Kors Access Scout Hutton MKT4024 Bedienungsanleitung

3 Oktober 2024
Auriol

Auriol IAN 43022 Bedienungsanleitung

2 Oktober 2024
Michael Kors

Michael Kors Kors Access Sofie MKT5039 Bedienungsanleitung

2 Oktober 2024
Citizen

Citizen CAL 5513 Bedienungsanleitung

1 Oktober 2024