Casio AW-591-2AER Bedienungsanleitung

Casio betrachten AW-591-2AER

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio AW-591-2AER (4 Seiten) in der Kategorie betrachten. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
1
Operation Guide 4778
MA0610-EA
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
• Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background.
All sample displays in this manual are shown using dark
figures on a light background.
For indicators, “On” is indicated by a dark indicator on
the positive (dark-on-light) display, and by a light
indicator on the negative (light-on-dark) display.
[Negative]
[Positive]
General Guide
• Press C to change from mode to mode.
• In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Press .
Timekeeping Mode World Time Mode Countdown Timer Mode Stopwatch Mode Alarm Mode Hand Setting Mode
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
• In the Timekeeping Mode, you can press to change the display format as shownD
below.
Day of week Month – Day Hour :
Minutes
Seconds PM indicator
Day of the Week Month – Day Hour : Minutes
Press
.
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST), your Home City code (the code for the city where you
normally use the watch), the 12/24-hour format, and the illumination duration.
• This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
• Note that all of the times for the World Time Mode city codes are displayed in
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
• After you correctly set your Home City time and date, you can set the watch up for
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C twice to move the flashing to the Home City
code setting (see the illustration below), and then use
B D and to select the code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table”.
3. Press C to move the flashing in the sequence shown below to select the other settings.
Seconds DST Home City Code Hour Minutes
Day Month Year 12/24-Hour FormatIllumination Duration
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (ON) and
Standard Time (
OF)
Change the Home City code
Change the hour or minutes
Toggle between 12-hour ( ) and 24-hour12H
(24H) timekeeping
Change the year
Change the month or day
Select one second ( ) or three seconds ( )
as the illumination duration
Do this:
Press .D
Press .D
Use D (east) and B (west).
Use ).D (+) and B (–
Press .D
Use ).D (+) and B (–
Press .D
5. Press A to exit the setting screen.
• Resetting the seconds only (without changing the DST, Home City code, hour, or
minute setting) causes the analog minute hand setting to be adjusted automatically.
• See “Digital Time Daylight Saving Time (DST) Setting below for details about the”
DST setting.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• For details about illumination duration, see “ ”Illumination .
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
2
Operation Guide 4778
DST indicator
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down until the secondsA
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (
ON
displayed) and Standard Time (
OF displayed).
4. Press A to exit the setting screen.
• The DST indicator appears on the Timekeeping, Alarm,
and Hand Setting Mode to indicate that Daylight Saving
Time is turned on.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by
20 seconds.
• Holding down advances the analog time setting atD
high speed.
• If you need to advance the analog time setting a long way, hold down until theD
time starts advancing at high speed, and then press . This locks the high-B
speed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
4. Press A to exit the setting screen.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
• To return to the Timekeeping Mode, press C.
City code
Current time for the
selected city code
World Time
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city
In the World Time Mode, press to scroll eastwardlyD
through city codes.
• For full information about city codes, see the “City Code
Table”.
• If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode
time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary
adjustments.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
• Note that you cannot switch between Standard Time
and Daylight Saving Time while GMT is selected as the
city code.
SecondsSeconds
Minutes
DST indicator
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
• See “To configure the countdown timer for information”
about setting up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
• Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing , or you canD
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
• When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
• When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
• Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
• 30 seconds before the end of the countdown, the watch emits four short beeps.
• The watch emits a short beep for each of the last 10 seconds of the countdown.
• If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under To use the countdown timer“ ” to
display it.
2. Press to move the flashing in the sequence shownC
below to select other settings.
Start Time Auto-repeat
Progress Beeper
3. When the setting you want to change is flashing, use
B D and to change it as described below.
Setting
Start Time
Auto-repeat
Progress Beeper
Screen Button Operation
Use D (+) and B (–) to change the setting.
• You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Press D to toggle auto-repeat on ( displayed) and off
( displayed).
Press D to toggle the progress beeper on (ON) and off
(OF).
4. Press A to exit the setting screen.
• You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press while in the Countdown Timer Mode to start theD
countdown timer.
• The countdown timer operation continues even if you
exit the Countdown Timer Mode.
• Press D while a countdown operation is in progress to
pause it. Press again to resume the countdown.D
• To completely stop a countdown operation, first pause it
(by pressing ), and then press . This returns theD A
countdown time to its starting value.
Seconds
Minutes
1/100 second
SPL indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing .C
To measure times with the stopwatch
Elapsed Time
Start Stop Re-start Stop Clear
Start Split
(SPL indicator
displayed)
Split release Stop Clear
Start Split Stop Split release Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
3
Operation Guide 4778
Alarm number
Alarm time
(Hour : Minutes)
On/Off status
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1 AL4through ), one is for a snooze alarm
(indicated by SNZ), and one is for the Hourly Time
Signal (indicated by SIG).
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1 AL4through . To set the snooze alarm, display the screen indicated
by SNZ.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D B (+) and (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. ( indicator).PM
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ
setting screen
To test the alarm
In the Alarm Mode, hold down to sound the alarm.D
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
• Turning on a one-time alarm (AL1through )AL4
displays the alarm on indicator on its Alarm Mode
screen.
• Turning on the snooze alarm (SNZ) displays the alarm
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen, and in all other modes.
• In all modes (except for the Alarm Mode), the alarm on
indicator is shown for any alarm that is currently turned
on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (SIG).
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
• The Hourly Time Signal on indicator is shown on the
display on the Alarm Mode Hourly Time Signal screen,
and in all other modes while the Hourly Time Signal is
turned on.
On/Off status
Hourly time signal
on indicator
On/Off status
Alarm on indicator
Snooze alarm
indicator
Auto light
switch indicator
Illumination
An LED (light-emitting diode) illuminate the display for
easy reading in the dark. The watch’s auto light switch
illuminates the display automatically when you angle the
watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” for more important
information.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C nine times so the illumination duration setting
screen is on the display.
3. While the illumination duration setting is flashing, press
D to toggle the setting between one second ( ) and
three seconds ( ).
4. Press A to exit the setting screen.
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on for about one second or
three seconds, whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Warning!
•••• • Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not surprise or distract
others around you.
•••• • When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode, hold down for about two seconds to toggle the auto light switch onB
(auto light switch indicator displayed) or off (auto light switch indicator not displayed).
• The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
• In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on.
To turn on illumination manually
In any mode (except when a setting screen is on the display), press to turn onB
illumination.
• The above operation turns on illumination regardless of the current auto light switch
setting.
•
You can use the procedure below to select either one second or three seconds as
the illumination duration. When you press
B
, the illumination will remain on for about
one second or three seconds, depending on the current illumination duration setting.
Parallel to ground More than 40
°
Mode
Timekeeping
World Time
Countdown
Timer
Stopwatch
Alarm
Hand Setting
Graphic Area A
Timekeeping Mode
seconds
World Time Mode
seconds
Countdown time
minutes
Stopwatch time
seconds
No indication
No indication
Graphic Area B
Timekeeping Mode
minutes
World Time Mode
minutes
Countdown time
seconds
Stopwatch time
1/10 seconds
No indication
No indication
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Areas
The following describes the information indicated by the graphic area in each mode.
Graphic area A
Graphic area B
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the PM indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch s batteries replaced.’
World Time
• All World Time Mode times are calculated from the current Home City time in the
Timekeeping Mode using UTC time differential values.
• The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
• The letters “ ” “ ”UTC is the abbreviation for Universal Time Coordinated , which is the
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.

Produktspezifikationen

Marke: Casio
Kategorie: betrachten
Modell: AW-591-2AER

Brauchst du Hilfe?

Wenn Sie Hilfe mit Casio AW-591-2AER benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung betrachten Casio

Casio

Casio GW-3000BD-1AER Bedienungsanleitung

9 Oktober 2024
Casio

Casio Edifice EFA-112D-1AVEF Bedienungsanleitung

7 Oktober 2024
Casio

Casio Baby-G BGA-200-1E2ER Bedienungsanleitung

6 Oktober 2024
Casio

Casio MTP-1302D-7A1VEF Bedienungsanleitung

1 Oktober 2024
Casio

Casio Baby-G BG-5600WH-7ER Bedienungsanleitung

30 September 2024
Casio

Casio Edifice EF-316D-1AVEF Bedienungsanleitung

25 September 2024
Casio

Casio GW-A1100-1A3ER Bedienungsanleitung

23 September 2024
Casio

Casio G-Shock GMA-B800 Bedienungsanleitung

21 September 2024
Casio

Casio DW-5600E-1VER Bedienungsanleitung

20 September 2024
Casio

Casio LW-S200H-8AEF Bedienungsanleitung

16 September 2024

Bedienungsanleitung betrachten

Neueste Bedienungsanleitung für -Kategorien-

Citizen

Citizen Cal 411X Bedienungsanleitung

7 Oktober 2024
Jaguar

Jaguar J627 Bedienungsanleitung

6 Oktober 2024
Citizen

Citizen CAL 4633 Bedienungsanleitung

5 Oktober 2024
Auriol

Auriol IAN 277495 Bedienungsanleitung

4 Oktober 2024
La Crosse Technology

La Crosse Technology WT-941 Bedienungsanleitung

4 Oktober 2024
Spin Master

Spin Master Dumas SP-5081-11 Bedienungsanleitung

4 Oktober 2024
Michael Kors

Michael Kors Kors Access Scout Hutton MKT4024 Bedienungsanleitung

3 Oktober 2024
Auriol

Auriol IAN 43022 Bedienungsanleitung

2 Oktober 2024
Michael Kors

Michael Kors Kors Access Sofie MKT5039 Bedienungsanleitung

2 Oktober 2024
Citizen

Citizen CAL 5513 Bedienungsanleitung

1 Oktober 2024