Casio AQ-160W-1BVDF Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio AQ-160W-1BVDF (4 Seiten) in der Kategorie Horloge. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/casio/aq-160w-1bvdf/html/bg1.png)
1
Operation Guide 3319/3781
MA0503-EA
About This Manual
•The operational procedures for Modules 3319 and 3781
are identical. All of the illustrations in this manual show
Module 3319.
•Button operations are indicated using the letters shown
in the illustration.
•All of the displays in this manual show black-on-white.
•For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
•Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Module 3319
Module 3781
Press .
Timekeeping Mode World Time Mode Countdown Timer Mode Stopwatch Mode Alarm Mode Hand Setting Mode
General Guide
•Press C to change from mode to mode.
•In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
•In the Timekeeping Mode, you can press to change the display format as shownD
below.
[Module 3319]
Day of week
Seconds
PM indicator Month – Day
Hour
Press .
Day of the Week Month – Day
Minutes
[Module 3781]
Da
y
of week Seconds
PM indicator
Month – Da
y
Hour
Press .
Day of the Week Month Day–
Minutes
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST), your Home City code (the code for the city where you
normally use the watch), the 12/24-hour format, and the illumination duration.
•This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
•Note that all of the times for the World Time Mode city codes are displayed in
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
•After you correctly set your Home City time and date, you can set the watch up for
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C twice to move the flashing to the Home City
code setting (see the illustration below), and then use
B D and to select the code you want.
•Make sure you select your Home City code before
changing any other setting.
•For full information on city codes, see the “City Code
Table”.
3. Press C to move the flashing in the sequence shown below to select the other settings.
Seconds DST Home City Code Hour Minutes
Day Month Year 12/24-Hour FormatIllumination Duration
Screen
*1
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (
ON) and
Standard Time (
OF)
Change the Home City code
Change the hour or minutes
Toggle between 12-hour ( ) and 24-hour12H
(24H) timekeeping
Change the year
Change the month or day
Select three seconds or one second as the
illumination duration
Do this:
Press .D
Press .D
Use D (east) and B (west).
Use ).D (+) and B (–
Press .D
Use ).D (+) and B (–
Press .D
4. When the setting you want to change is flashing, use B and D to change it as
described below.
*1 Some models display the time as .
Module 3319
Module 3781
5. Press A to exit the setting screen.
•Resetting the seconds only (without changing the DST, Home City code, hour, or
minute setting) causes the analog minute hand setting to be adjusted automatically.
•See “Digital Time Daylight Saving Time (DST) Setting below for details about the”
DST setting.
•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
•For details about illumination duration, see “ ”Display Illumination .
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press A to exit the setting screen.
•The DST indicator appears on the Timekeeping, Alarm,
and Hand Setting Mode to indicate that Daylight Saving
Time is turned on.
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/casio/aq-160w-1bvdf/html/bg2.png)
2
Operation Guide 3319/3781
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by
20 seconds.
•Holding down advances the analog time setting atD
high speed.
•If you need to advance the analog time setting a long way, hold down until theD
time starts advancing at high speed, and then press . This locks the high-B
speed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
4. Press A to exit the setting screen.
•The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
•To return to the Timekeeping Mode, press C.
Current time for the
selected city code
City
code
Module 3319
Module 3781
World Time
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.
•All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city
In the World Time Mode, press to scroll eastwardlyD
through city codes.
•For full information about city codes, see the “City Code
Table”.
•If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode
time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary
adjustments.
Module 3319
Module 3781
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time ( displayed) and StandardDST
Time (DST not displayed).
•The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
•Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
•Note that you cannot switch between Standard Time
and Daylight Saving Time while GMT is selected as the
city code.
Seconds Minutes
Module 3319
Module 3781
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
•All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
•See “To configure the countdown timer for information”
about setting up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
•Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing , or you canD
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
•When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
•When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Setting
Start Time
Auto-repeat
Progress Beeper
Screen Button Operation
Use D (+) and B (–) to change the setting.
•You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Press D to toggle auto-repeat on ( displayed) and off
( displayed).
Press D to toggle the progress beeper on (ON) and off
(OF).
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
•Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
•30 seconds before the end of the countdown, the watch emits four short beeps.
•The watch emits a short beep for each of the last 10 seconds of the countdown.
•If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
•If the countdown start time is not displayed, use the
procedure under To use the countdown timer“ ” to
display it.
2. Press to move the flashing in the sequence shownC
below to select other settings.
Start Time Auto-repeat
Progress Beeper
3. When the setting you want to change is flashing, use
B D and to change it as described below.
4. Press A to exit the setting screen.
•You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press while in the Countdown Timer Mode to start theD
countdown timer.
•The countdown timer operation continues even if you
exit the Countdown Timer Mode.
•Press D while a countdown operation is in progress to
pause it. Press again to resume the countdown.D
•To completely stop a countdown operation, first pause it
(by pressing ), and then press . This returns theD A
countdown time to its starting value.
1/100 second
Seconds
Minutes
Module 3319
Module 3781
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•The display range of the stopwatch is 59 minutes,
59.99 seconds.
•The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing .C
To measure times with the stopwatch
Elapsed Time
Start Stop Re-start Stop Clear
Start Split
( displayed) SPL
Split release Stop Clear
Start Split Stop Split release Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/casio/aq-160w-1bvdf/html/bg3.png)
3
Operation Guide 3319/3781
Alarm time
(Hour Minutes)
On/Off status
Alarm
number
Module 3319
Module 3781
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
•There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1 AL4through ), one is for a snooze alarm
(indicated by SNZ), and one is for the Hourly Time
Signal (indicated by SIG).
•All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Hourly time signal on
indicator
On/Off status
Module 3319
Module 3781
Snooze alarm indicator
On/Off status
Alarm on indicator
Module 3319
Module 3781
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (SIG).
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
•The Hourly Time Signal on indicator is shown on the
display on the Alarm Mode Hourly Time Signal screen,
and in all other modes while the Hourly Time Signal is
turned on.
Auto light switch indicator
Module 3319
Module 3781
Display Illumination
Display illumination uses an EL (electro-luminescent)
panel that causes the entire display to glow for easy
reading in the dark. The watch’s auto light switch
automatically turns on display illumination when you angle
the watch for reading towards your face.
•The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
•See “Illumination Precautions” for more important
information.
To illuminate the display
In any mode (except when a setting screen is on the display), press to turn onB
illumination.
•The above operation turns on illumination regardless of the current auto light switch
setting.
•
You can use the procedure below to select either one second or three seconds as
the illumination duration. When you press
B
, the illumination will remain on for about
one second or three seconds, depending on the current illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C nine times so the illumination duration setting
screen is on the display.
3. While the illumination duration setting is flashing, press
D to toggle the setting between one second ( ) and
three seconds ( ).
4. Press A to exit the setting screen.
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on for about one second or
three seconds, whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
Parallel to ground More than 40
°
Mode
Timekeeping
World Time
Countdown
Timer
Stopwatch
Alarm
Hand Setting
Graphic Area A
Timekeeping Mode
seconds
Timekeeping Mode
seconds
Countdown time
minutes
Stopwatch time
seconds
No indication
No indication
Graphic Area B
Timekeeping Mode
minutes
Timekeeping Mode
minutes
Countdown time
seconds
Stopwatch time
1/10 seconds
No indication
No indication
Mode
Timekeeping
World Time
Countdown Timer
Stopwatch
Alarm
Hand Setting
Graphic Area
Timekeeping Mode seconds
Timekeeping Mode seconds
Countdown time minutes
Stopwatch time seconds
No indication
No indication
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Area
The following describes the information indicated by the graphic area in each mode.
[Module 3319]
Graphic area
[Module 3781]
Graphic area B
Graphic area A
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
•To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1 AL4through . To set the snooze alarm, display the screen indicated
by SNZ.
•The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
•This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D B (+) and (–) to change it.
•When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off .
•Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
•To stop the alarm tone after it starts to sound, press any button.
•Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ
setting screen
To test the alarm
In the Alarm Mode, hold down to sound the alarm.D
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
•Turning on a one-time alarm (AL1through )AL4
displays the alarm on indicator on its Alarm Mode
screen.
•Turning on the snooze alarm (SNZ) displays the alarm
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen, and in all other modes.
•In all modes (except for the Alarm Mode), the alarm on
indicator is shown for any alarm that is currently turned
on.
•The alarm on indicator flashes while the alarm is
sounding.
•The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Warning!
••
••
•Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged in
any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not surprise or distract
others around you.
••••
•When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode, hold down for about two seconds to toggle the auto light switch onB
(auto light switch indicator displayed) or off (auto light switch indicator not displayed).
•The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
•In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on.
Produktspezifikationen
Marke: | Casio |
Kategorie: | Horloge |
Modell: | AQ-160W-1BVDF |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Casio AQ-160W-1BVDF benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Horloge Casio
![Casio](/images/logos/casio.png)
5 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
3 September 2024
![Casio](/images/logos/casio.png)
2 September 2024
![Casio](/images/logos/casio.png)
2 September 2024
Bedienungsanleitung Horloge
- Horloge Clas Ohlson
- Horloge Velleman
- Horloge ADE
- Horloge Auriol
- Horloge Eurochron
- Horloge Irox
- Horloge MarQuant
- Horloge Prologue
- Horloge Renkforce
- Horloge Braun
- Horloge Alpina
- Horloge Mitsubishi
- Horloge Topcom
- Horloge Seiko
- Horloge Fossil
- Horloge Garmin
- Horloge Jaguar
- Horloge Lotus
- Horloge Michael Kors
- Horloge Skagen
- Horloge Bushnell
- Horloge Citizen
- Horloge Dugena
- Horloge Krontaler
- Horloge Mondaine
- Horloge Epson
- Horloge Westfalia
- Horloge Suunto
- Horloge BML
- Horloge Swatch
- Horloge Tissot
- Horloge Adidas
- Horloge Ascot
- Horloge Asics
- Horloge Bruno Söhnle
- Horloge Edox
- Horloge Lorus
- Horloge Maurice Lacroix
- Horloge Omega
- Horloge Grand Seiko
- Horloge Armani
- Horloge Bering
- Horloge Breitling
- Horloge Breo
- Horloge Bulova
- Horloge Christiaan Van Der Klaauw
- Horloge Daniel Steiger
- Horloge Davis
- Horloge Detomaso
- Horloge Diesel
- Horloge Ebel
- Horloge Elysee
- Horloge Executive
- Horloge Festina
- Horloge Fila
- Horloge Gant
- Horloge Girard-Perregaux
- Horloge Guess
- Horloge Hamilton
- Horloge Holzkern
- Horloge Hugo Boss
- Horloge Ice Watch
- Horloge Invicta
- Horloge IWC
- Horloge Jacques Lemans
- Horloge Junghans
- Horloge Lacoste
- Horloge Longines
- Horloge Luminox
- Horloge Orient
- Horloge Pulsar
- Horloge Puma
- Horloge Sinn
- Horloge Stührling
- Horloge Swiza
- Horloge Timberland
- Horloge Timex
- Horloge Torgoen
- Horloge Tudor
- Horloge TW Steel
- Horloge Versace
- Horloge Zenith
- Horloge Victorinox
- Horloge ETT
- Horloge Boss
- Horloge Oregon Scientific
- Horloge Spin Master
- Horloge Danish Design
- Horloge Digi-tech
- Horloge ESQ
- Horloge Ferrari
- Horloge GC Watches
- Horloge Haffstreuner
- Horloge Inter-Quartz
- Horloge Just
- Horloge Kalenji
- Horloge La Crosse
- Horloge Lambretta
- Horloge Marc Jacobs
- Horloge Meister Anker
- Horloge Misfit
- Horloge Movado
- Horloge Nike
- Horloge QQ
- Horloge Rado
- Horloge Rodania
- Horloge Rolex
- Horloge Ronda
- Horloge Skmei
- Horloge Spinnaker
- Horloge Tauchmeister
- Horloge Tommy Hilfiger
- Horloge Xonix
- Horloge Shinola
- Horloge Philip Watch
- Horloge Lucien Picard
- Horloge So & Co
- Horloge Nautica
- Horloge Obaku
- Horloge Christopher Ward
- Horloge Audemars Piguet
- Horloge Pilgrim
- Horloge Lars Larsen
- Horloge DMC
- Horloge Raketa
- Horloge Julie Julsen
- Horloge KRAEK
- Horloge PANERAI
- Horloge HYT
Neueste Bedienungsanleitung für -Kategorien-
![DMC](/images/pdf_free.png)
7 September 2024
![DMC](/images/pdf_free.png)
7 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024
![Seiko](/images/pdf_free.png)
6 September 2024