Caliber RMD 575BT Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Caliber RMD 575BT (41 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/41
Remove the Old Unit from the Dashboard
DIN Front Mount
DO NOT DISCONNECT WIRES
AT THIS TIME!
2. Insert the keys supplied with the
old unit into both sides of the unit
as shown in figure below until
they click. Pull to remove the old
unit from the dashboard.
1. Remove the outer trim frame.
INSTALLATION
Tools for Installation
Use the 2 removal wrenches of the old unit to take out the old unit and place with this brand new car radio. The following tools and sup-
plies may also be needed for the installation:
Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper /Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill
Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for Power Connections /14-16 Gauge Speaker Wires
The above are not supplied.
Before you install
Automotive audio equipment installations can be challenging even to the most experienced of installation technicians. We strongly rec-
ommend that this unit should be professionally installed by a VAT registered installer (this is a requirement to validate the warranty).
IMPORTANT: Remove the two transport screws from the top fo the unit before installing.
Mark Polarity of the Speaker Wires
Marking the polarity of the speaker wires will make it easier to connect the existing speakers to your car radio. Consult wiring diagram
of existing head unit before disconnecting any wires. If you are not positive of the polarity of the existing wires from the speakers to the
head unit, install new wires.
1. While the old unit is playing, disconnect the wires from one speaker.
2. Take a length of masking tape and fold it around the wire so it forms a flag.
3. On the masking tape mark the polarity of the speaker wires (+&-), as well as left or right, and front or rear.
4. Double check that you marked the first speaker correctly by checking that the speaker wires are the same at the head unit.
5. Repeat this procedure for all of the speakers.
6. Mark the power, ground, and any other wires also.
Produktspezifikationen
Marke: | Caliber |
Kategorie: | Autoradio |
Modell: | RMD 575BT |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Caliber RMD 575BT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autoradio Caliber
5 Februar 2024
21 Dezember 2023
30 November 2023
24 November 2023
13 November 2023
23 August 2023
1 Juli 2023
18 Juni 2023
6 Juni 2023
3 Juni 2023
Bedienungsanleitung Autoradio
- Autoradio Clatronic
- Autoradio Manta
- Autoradio Medion
- Autoradio SilverCrest
- Autoradio Sony
- Autoradio Panasonic
- Autoradio AEG
- Autoradio Denver
- Autoradio Renkforce
- Autoradio Telefunken
- Autoradio Trevi
- Autoradio Blaupunkt
- Autoradio Grundig
- Autoradio Kenwood
- Autoradio Daewoo
- Autoradio Pyle
- Autoradio Aiwa
- Autoradio Auna
- Autoradio Pioneer
- Autoradio JBL
- Autoradio JVC
- Autoradio Muse
- Autoradio Akai
- Autoradio Dual
- Autoradio Hyundai
- Autoradio Orion
- Autoradio Skoda
- Autoradio Elta
- Autoradio Sencor
- Autoradio Mercedes-Benz
- Autoradio Harman Kardon
- Autoradio Magnat
- Autoradio XOMAX
- Autoradio Alpine
- Autoradio Volkswagen
- Autoradio Volvo
- Autoradio Opel
- Autoradio MB Quart
- Autoradio Overmax
- Autoradio Rockford Fosgate
- Autoradio Crunch
- Autoradio Clarion
- Autoradio Mac Audio
- Autoradio Becker
- Autoradio ESX
- Autoradio Zenec
- Autoradio VDO
- Autoradio SPC
- Autoradio Roadstar
- Autoradio Audison
- Autoradio Macrom
- Autoradio Boss
- Autoradio Renault
- Autoradio Kicker
- Autoradio Jensen
- Autoradio DLS
- Autoradio Fusion
- Autoradio Ground Zero
- Autoradio Lanzar
- Autoradio Mtx Audio
- Autoradio Rodek
- Autoradio Sirius
- Autoradio VDO Dayton
- Autoradio RetroSound
- Autoradio Lark
- Autoradio SoundMAX
Neueste Bedienungsanleitung für -Kategorien-
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024