Bunn ICB Infusion Series Soft Heat Dual Volt SST Bedienungsanleitung

Bunn Kaffeemaschine ICB Infusion Series Soft Heat Dual Volt SST

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Bunn ICB Infusion Series Soft Heat Dual Volt SST (4 Seiten) in der Kategorie Kaffeemaschine. Dieser Bedienungsanleitung war für 33 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

www.bunn.com

ICB SH

ICB SH TWIN

Faucet Side Car Relocation

Instructions

TO BE PERFORMED BY QUALIFIED PERSONNEL

These instructions are intended for relocating the facuet side car on an ICB SH brewer. Ensure all tools are present before

performing the installation.

WARNING: Disconnect the brewer from the power source before performing the procedure. Ensure the

water is drained from the tank and be aware that many internal parts can be extremely hot; allow contents of

tank to cool before proceeding.

Note: If technical assistance is needed, please call 1-800-286-6345

Tools Required:

8/32 socket/wrench

Flat Blade Screwdriver

• Disconnect power to the brewer.

• Remove the screws that secure the front

panel to the brewer (6 screws).

STEP 1

• Carefully remove the front panel of the

brewer.

STEP 2

ICB SH Faucet Side Car Installation Instructions

• Remove the three screws that secure the

cover to the faucet side car.

• Remove the cover.

STEP 3

• Open the faucet handle to drain water from

the tank. Keep the faucet handle open until

water is no longer dispensing.

• Remove the hose snap clamp that secures

the tube to the faucet shank.

• Carefully remove the hose from the faucet

shank.

STEP 4

• Remove the two 8/32 nuts, two washers

and base screw from the faucet side car.

• Remove the black silicone grommet.

STEP 5

• Completely remove the faucet side car,

spacer and plate assembly from the left

side of the brewer.

STEP 6

Remove Cover

Remove Hose Snap

Remove Tube

Remove Nuts ,

Washers, Screws

& grommet

Spacer

Plate Assembly

Faucet Side Car

• Remove the plastic badge from the right

side of the brewer.

• Install the plastic badge on the left side of

the brewer to cover the panel holes.

• Install the base screw that was removed

in step 5.

STEP 7

• Remove the snap-in fastener from the

faucet side car and place into the hole

directly above as shown.

STEP 8

ICB SH Faucet Side Car Installation Instructions

• Place the plate assembly into the

uncovered holes on the inside of the right

panel.

• Place the spacer on the outside of the

right panel on the plate assembly.

STEP 9

• Remove the base screw on the right side.

STEP 10

• Align the faucet side car to the right side

of the brewer.

• Secure the faucet side car using the

washers and screws that were removed in

step 5.

STEP 11

• Insert the black grommet into the large

tubing hole. This is the same grommet

removed in step 5.

• Secure the base screw to the faucet side

car.

STEP 12

Plastic Badge

Secure

Remove

Fastener

Insert

Fastener

Plate Assembly

Spacer

Remove Base Screw

Align

Secure with

Washers &

Screws

Grommet

Produktspezifikationen

Marke:	Bunn
Kategorie:	Kaffeemaschine
Modell:	ICB Infusion Series Soft Heat Dual Volt SST

Brauchst du Hilfe?

Wenn Sie Hilfe mit Bunn ICB Infusion Series Soft Heat Dual Volt SST benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage