Buffalo TS4400R Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Buffalo TS4400R (4 Seiten) in der Kategorie Server. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
The TS4000 series will not work without disks. Please prepare 1 or more un-partitioned
HDDs for the setup process. Use either new HDD(s) or delete all partitions (and
therefore all data) with a partition editor before you start with existing HDD(s).
Step by step
1. Mount one or more HDDs to a frame and insert it in the TeraStation™.
2. Prepare the MicroSD and the USB adapter and insert the USB
adapter into a USB 2.0 port, connect power and network.
3. Move the boot switch to USB position.
4. Boot the TeraStation™.
Now the unit gives after some minutes a tone, the display
goes red and it says “push function button to start”.
5. Push the function button until beep sounds.
The display status color will be blue and sequence through these messages:
Recovery Preparing
System Recovering
FW/Updating
Recovery Finished, “Change Boot SW”
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
6. The TeraStation™ will shut down and the Power button will no
longer be lit green. The display and Info light stay on.
7. Remove the USB adapter, move the switch on the
back to HDD, press the power button
If you use just one drive you will have a brief warning for missing
HDDs and afterwards the TeraStation™ will operate normally.
If you use more than one drive: The first HDD is mounted and will work normally
and the other HDDs are mounted but not yet formatted. The display will therefore
turn red and the status LEDs of all unformatted drives will show red as well.
The warning, red display, and red LEDs will remain until you finish formatting all HDDs.
8. Now please install the NAS Navigator on your computer and click
‘Refresh’ to reveal your new TeraStation™ 4000. Right click on it and select
‘Settings’. A browser window will launch the admin interface. It’s also
possible to access the admin interface by entering the TS4000 series IP
address (shown on the TS’s display) directly into a browser window.
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
9. Format all unformatted HDDs via the admin interface. Once formatting
is completed the status in the admin page will change to ‘Formatted’
please wait to see this before continuing, depending on HDD
capacity this could take approximately 8 minutes per drive.
Produktspezifikationen
| Marke: | Buffalo |
| Kategorie: | Server |
| Modell: | TS4400R |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Buffalo TS4400R benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Server Buffalo
26 Juli 2024
26 Juli 2024
24 Juli 2024
20 Juli 2024
20 Juli 2024
15 Juli 2024
15 Juli 2024
11 Juli 2024
9 Juli 2024
1 April 2024
Bedienungsanleitung Server
- Server Acer
- Server Asus
- Server Gigabyte
- Server HP
- Server Medion
- Server Linksys
- Server Netgear
- Server Megasat
- Server Toshiba
- Server Dell
- Server Lenovo
- Server Tripp Lite
- Server TRENDnet
- Server Western Digital
- Server AVerMedia
- Server Veritas
- Server Black Box
- Server Supermicro
- Server NEC
- Server Monacor
- Server Seagate
- Server Fujitsu
- Server D-Link
- Server QNAP
- Server Digitus
- Server LevelOne
- Server APC
- Server Cisco
- Server Synology
- Server Intellinet
- Server Eaton
- Server Hikvision
- Server Planet
- Server Asustor
- Server Dane Elec
- Server Iomega
- Server LaCie
- Server Quantum
- Server Siig
- Server Moxa
- Server StarTech.com
- Server ATen
- Server Axis
- Server B&B Electronics
- Server Infortrend
- Server Areca
- Server Origin Storage
- Server Lantronix
Neueste Bedienungsanleitung für -Kategorien-
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
27 Juli 2024