Broan PM250 Bedienungsanleitung

Broan Dunstabzugshaube PM250

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Broan PM250 (12 Seiten) in der Kategorie Dunstabzugshaube. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

PM250 SERIES

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you

have questions, contact the manufacturer at the address or telephone

number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and

lock service panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to prevent

backdrafting. Follow the heating equipment manufacturer’s guidelines

and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause

smoking and greasy spillovers that may ignite. Heat oils slowly on low

or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing

food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).

C. Clean ventilating fans frequently. Grease should not be allowed to

accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of

the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF

A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,

then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the

flames do not go out immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent

steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already

know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

INTENDED FOR DOMESTIC COOKING ONLY

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air

outside. Do not vent exhaust air into spaces within walls or ceilings

or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut

off the motor if it becomes overheated. The motor will restart when

it cools down. If the motor continues to shut off and restart, have the

hood serviced.

8. The bottom of the hood MUST NOT BE LESS than 24” and

recommended at a maximum of 30” above the cooktop for best capture

of cooking impurities.

9. Two installers are recommended.

10. Use with approved cord-connection kit only.

11. Please read specification label on product for further information and

requirements.

POWER

MODULE

NON-DUCTED RECIRCULATION

FILTER INSTALLATION

1. Remove the metal wires (Fig. 7) and discard them.

2. Install the Non-ducted recirculation Filter over the grease filter

and secure it with the metal wires supplied with the Non-ducted

recirculation Filter (Fig. 4).

WIRING

Note: This range hood must be properly grounded.

The unit should be installed by a qualified electrician in

accordance with all applicable national and local electrical codes.

Secure the conduit to the upper wiring hole through a conduit

connector.

Remove the (2) screws of the lateral wiring field cover and make

electrical connections. Connect both white leads to white supply lead

using suitable connector, connect black to black and green to green.

NON-DUCTED

RECIRCULATION

FILTER

INSTALL THE DUCTWORK

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Decide where the ductwork will run between the hood and the

outside (Refer to Figure 1).

2. A straight, short duct run will allow the hood to perform most

efficiently.

3. Long duct runs, elbows, and transitions will reduce the performance

of the hood. Use as few of them as possible. Larger ducting may

be required for best performance with longer duct runs.

4. Install a roof or wall cap. Connect round metal ductwork to cap and

work back towards hood location. Use duct tape to seal the joints

between ductwork sections.

INSTALL THE HOOD

NOTE: the hood has to be installed, inside the cabinet, at minimum 1”

from the rear wall cabinet and at 3” from the front wall cabinet.

The internal height of cabinet has to be minimum 16”.

The hood should be mounted centered over the cook top burners.

1. Cut a hole in the bottom of the cabinet, using the dimensions shown

in Fig. 2.

2. Take off the (4) “A” screws and remove the metal grid (Fig. 3).

3. NOTE: For installations where the Power Pack is less than 30” above

cook top, it is recommended that the Power Pack be mounted into

a metal liner or non-combustible material. This will allow easier

cleaning and provide protection to the cabinetry (Fig.3A).

4. Insert the hood in the cabinet (Fig. 3) or metal liner (Fig. 3A) and

secure with the (4) “B” mounting sheet metal screws.

(Fig. 3 - wood bottom installation; recommended thickness 1/2”-

3/4”).

(For alternate mounting, use machine screws with washers and

nuts. This alternate mounting method needs to be done prior to

installation of metal liner).

5. In the Non-Ducted Recirculation Configuration, install the Non-

ducted recirculation Filter before replacing the grid (see section

“Non-ducted recirculation filter installation”).

6. Replace the grid after wiring is completed.

ROOF CAP

ROUND

DUCT

POWER

MODULE

WALL

CAP

7”

ROUND

ELBOW

24” TO 30” ABOVE

COOKING SURFACE

10-1/4”

CUT A HOLE IN THE BOTTOM OF THE CABINET

19-1/2”

FIG. 1

FIG. 2

FIG. 4

METAL WIRES

CONNECT DUCTWORK

Ducted Configuration

1. Use 7” round metal duct to connect the discharge collar on the

hood to the ductwork above. An optional 7” round damper may be

used (purchased seperately).

2. Use to make all joints secure and air tight.duct tape

Non-Ducted Recirculation Configuration

1. Connect a 7” round metal duct to the discharge opening so that

the air is sent outside the cabinet and sent back into the room.

2. Use to make all joints secure and air tight.duct tape

LATERAL

WIRING FIELD

COVER

FIG. 5

GRID

FIG. 3

METAL LINER

FIG.3A

MAINTENANCE

ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CARRYING

OUT ANY OPERATIONS ON THE APPLIANCE.

Grease Filter

The grease filter should be cleaned frequently. Use a warm detergent

solution. Grease filter is dishwasher safe.

To remove the grease filter: remove the (4) screws and take off the

metal grid. Take off the metal wires and remove the grease filter.

Non-Ducted Recirculation Filter

The Non-Ducted Recirculation filter should be changed every 6 months.

To remove the Non-Ducted Recirculation filter:

1. Remove the grid taking off the (4) “A” screws 3.9x6mm (Fig. 3).

2. Remove the metal wires (Fig. 4) and replace the Non-ducted

recirculation Filter.

Cleaning

Occasional care will help preserve its fine appearance.

• Clean with warm water and mild detergent only.

• Follow all cleaning by rinsing with clear water.

• Wipe dry with clean, soft cloth.

Light bulbs

This range hood requires two 40-Watt light bulbs (not included).

To change bulbs:

1. Remove the 2.9x9.5mm screw securing the light fitting.

2. Pull down lens to remove.

3. Replace with light bulbs of the same type (MAX 40W, 120V,

Candelabra Base Bulb). CAUTION: BULB MAY BE HOT!

SERVICE PARTS

KEY NO. PART NO. DESCRIPTION

5 97018550 Grid (Silver)

9 99010370 Grease Filter

23 B03295095 Upper Lampholder

24 B03295094 Lower Lampholder

27 98010831 Metal Wire

28 B02300280 Lampholder

29 B03294757 Light Fitting

230 98010828 Controls Closing

236 99030347 Blower Switch (Black)

237 99030342 Light Switch (Black)

332 98010834 Cover Controls

415 99400048 Strain Relief Bushing

Not shown 97018559 Hardware Package

CAS R730090 Blower Assembly

- 97018557 Socket Assembly

(Includes key No.24, 23, 28)

- - “40 Watt Max.Candelabra

Bulbs not included”

- B08999040 Non-Ducted Filter Kit

(purchased separately)

GREASE

FILTER

METAL WIRES

FIG. 7

FIG. 8

FIG. 6

OPERATION

Controls

Light switch: turns the lamps on and off.

Blower switch: makes it possible to select the motor operating

speed.

OFF

Produktspezifikationen

Marke:	Broan
Kategorie:	Dunstabzugshaube
Modell:	PM250

Brauchst du Hilfe?

Wenn Sie Hilfe mit Broan PM250 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Dunstabzugshaube Broan

Broan EWS1366SS Bedienungsanleitung

2 September 2024

Broan BCSEK136BL Bedienungsanleitung

20 August 2024

Broan BCDF136SS Bedienungsanleitung

17 August 2024

Broan BCSD142WW Bedienungsanleitung

17 August 2024

Broan B5936SS Bedienungsanleitung

16 August 2024

Broan BKSA130SS Bedienungsanleitung

16 August 2024

Broan BWS2304BLS Bedienungsanleitung

16 August 2024

Broan BKSH130WW Bedienungsanleitung

16 August 2024

Broan 373001 Bedienungsanleitung

16 August 2024

Broan 403004 Bedienungsanleitung

16 August 2024

Bedienungsanleitung Dunstabzugshaube

Neueste Bedienungsanleitung für -Kategorien-

Pelgrim ISW990 Bedienungsanleitung

16 Oktober 2024

Amana UVL6048JSS Bedienungsanleitung

16 Oktober 2024

Maytag UVL6048JSS Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GTW Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GW Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GB Bedienungsanleitung

16 Oktober 2024

Freggia CHS46B Bedienungsanleitung

16 Oktober 2024

Freggia CHS45X Bedienungsanleitung

16 Oktober 2024

Freggia CHS45W Bedienungsanleitung

16 Oktober 2024

Freggia CHS45B Bedienungsanleitung

16 Oktober 2024