Britax-Römer Advansafix IV R Bedienungsanleitung

Britax-Römer Autositz Advansafix IV R

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Britax-Römer Advansafix IV R (3 Seiten) in der Kategorie Autositz. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

BRITAX RÖMER

Kindersicherheit GmbH

Theodor-Heuss-Straße 9

89340 Leipheim

Germany

+49 (0) 8221 3670 199

BRITAX Excelsior Limited

1 Churchill Way West

Andover

Hampshire SP10 3UW

United Kingdom

+44 (0) 1264 386034

BRITAX Nordiska Barn AB

Jörgen Kocksgatan 4

SE-211 20 Malmö

Sweden

www.britax-roemer.com | hello@britax-roemer.com

BRITAX RÖMER Child Safety EMEA

30 32

20 32 26

20 21

19 19

08 21 32

1. GENERAL SAFETY INSTRUCTIONS 2. USE IN THE VEHICLE 3. APPROVAL 4. CARE AND MAINTENANCE

6. Release the two press studs on the seat cover and fold the cover forwards.

Whendoing so, pull the SecureGuard 26 out of the cover.

7. Loosen the 5-point harness 09 on the child seat as far as possible.

Tip: Pull the two shoulder straps forward while pressing the adjustment button 18.

8. Release the two opened shoulder cushions 19 from the Velcro strip and fold them

around the shoulder straps 08 .

DANGER Make sure that the shoulder straps 08 pass correctly through theshoul-

der cushions 19.

9. Remove the belt clips 21 from the recess provided on the 44 inside of the backrest.

10. Raise the grey release plate 32 and push it along with the SecureGuard 26 towards

the backrest 30 .

11. Turn the grey release plate 32 around so that the harness buckle 20 is at the top

and the SecureGuard 26 . is at the bottom

12. Store the SecureGuard 26 in the recess provided and push the grey release plate

32 back into its holder until it engages with an audible click.

13. Pass the harness buckle 20 through the slot in the cover which is nearer

tothebackrest.

We recommend using the 5-point harness as long as possible and making the conver-

sion only when your child starts to weigh more than 15 kg and has reached the highest

position of the headrest.

1. Loosen the 5-point harness on the child seat as far as possible 09 .

2. Open the harness buckle 20 and place the belt clips 21 in the belt guides

onthesides.

3. Loosen the press studs on the backrest and fold the upper half of the cover up-

wards and the lower half downwards.

4. Insert the belt clips 21 in the recess provided on the 44 inside of the backrest.

5. Open the two shoulder cushions 19 by the Velcro fasteners on the side.

6. Push the Velcro strip of the two opened shoulder cushions 19 under the back-

restcover and attach it to the ﬂeece strip provided.

Check that the two shoulder cushions are not overlapping.

7. Pull the adjusting strap 22 to tighten the harness.

8. Release the two press studs on the seat cover and fold the cover forwards.

Whiledoing this, pull the harness buckle 20 out of the cover.

9. Raise the grey release plate 32 and push it along with the harness buckle 20

towards the backrest 30.

10. Turn the grey release plate around 32 so that the ( ) SecureGuard B 26 is at the top

and the ( ) harness buckle A 20 .is at the bottom

11. Stow the harness buckle 20 in the recess provided and push the grey release plate

32 back into the holder until it engages with an audible click.

12. Pass the SecureGuard 26 through the slot in the cover with sow-on .B

13. Close the two bottom press studs on the cover.

14. Close the two top press studs on the cover.

15. Close the two press studs on the upper cover of the headrest.

11. REMOVING THE 5-POINT HARNESS AND RE-ATTACHING SECUREGUARD

12. RE-ATTACHING THE 5-POINT HARNESS AND REMOVING SECUREGUARD

9 to 36 kg

9 m. ~ 12 y.

www.britax-roemer.com

User instructions

ADVANSAFIX IV R

Child seat back

1. Slide the headrest 07 to the lowest position.

2. Press the safety catch at the centre of the group change switch

45 , at the same

time moving it to the lower position for use with Group 1 (9-18 kg).

Child seat front

3. Fold the lower part of the headrest cover upwards and lay it over the headrest.

4. Open the two press studs on the inside of the headrest cover.

5. Release the two press studs on the back of the cover .

Please refer to your vehicle’s instruction manual for instructions on how to use child

restraint systems. ISOFIX & Top Tether anchorage This seat can be used in vehicles with

points, ISOFIX & 3-point harness (see type list) 3-point in vehicles with and in vehicles with

harness.

Please refer to your vehicle’s instruction manual for information on the seats approved

as .child seats for weight class 9 to 36 kg

The ADVANSAFIX IV R is approved for three dierent installation methods:

a) This means that the child seat may only be used in vehicles listed on the enclosed vehicle type list.

This type list is constantly being updated.

The latest version can be obtained from us or from our website at www.britax.com

You can install your child seat as follows:

Facing forwards

(in the direction of travel)

Yes

Facing backwards

(against the direction of travel)

No 1)

With 2-point harness No

With 3-point harness

2) Yes

with ISOFIX ﬁxing points

(between seat surface and backrest)

Yes

On front passenger seat Yes

On outer rear seat Yes

On centre rear seat

(with 3-point harness) Yes 4)

1) Installation is permitted on backward-facing car seats (e.g. in a van or minibus) only if these seats are

also approved for carrying adults. The seat must not be within the activated range of an airbag.

2) The safety belt must be approved to ECE R 16 (or a comparable standard), which is indicated on the

harness test label by an "E" or "e" inside a circle.

3) If there is a front airbag: Slide the car seat well back and follow the relevant instructions in the vehicle’s

instruction manual.

4) It cannot be used if there is only a 2-point belt available.

Group Installation method Approval type Section

of user

instructions

1 (9-18 kg) ISOFIX + Top Tether universal A

2/3 (15-36 kg) ISOFIT + car seat belt semi-universala) B1

2/3 (15-36 kg) Car seat belt universal B2

BRITAX RÖMER

Child seat

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

ADVANSAFIX IV R

I+II+III 9 to 36 kg

*ECE = European Standard for Child Safety Equipment

The child seat has been designed, tested and approved according to the require-

ments of the European Standard for Child Safety Equipment (ECE R 44/04).

The E certiﬁcation mark (in a circle) and approval number can be found

on the orange approval label (sticker on the child seat).

DANGER! The certiﬁcation is invalidated if you make any modiﬁcations to the

child seat. Only the manufacturer is permitted to make modiﬁcations to the child seat.

Never secure your child or the child seat with a 2-point belt. If you DANGER!

secure your child in the child seat with a 2-point belt only, this may cause serious

injuries to your child in the event of an accident and could even cause death.

TheWARNING!

ADVANSAFIX IV R

must be used exclusively for securing your

child in the vehicle. It is in no way suitable for use as a seat or toy in the home.

Please take the time to read these instructions carefully and always keep

them in the storage pouch provided

14 on the child seat for later reference.

The instructions must accompany the child seat if it is later passed on to athird

party.

DANGER! For the protection of your child:

• Before closing the vehicle door, check that neither your child nor any parts

of the child seat can get jammed in the door.

• In the event of an accident at a collision velocity greater than 10 km/h, it is pos-

sible that the child seat may be damaged without the damage being immediately

visible. In this case the child seat must be replaced. Please dispose of it properly.

• Always have the child seat examined if it has been damaged (e.g. if it falls to the

ground).

• Regularly check all important parts for damage. In particular, ensure that

all the mechanical parts are fully functional.

• Never lubricate any parts of the child seat with grease or oil.

•

Never leave your child unattended in the child seat in the vehicle.

• Have your child enter and exit the vehicle on the pavement side only.

• When not in use, protect the child seat from direct exposure to sunlight.

The child seat can become very hot in direct sunshine. Children's skin is sensi-

tive and could be harmed as a result.

•

7KHPRUHVQXJO\WKHEHOW¿WVRYHU\RXUFKLOGVERG\WKHVDIHU\RXUFKLOGZLOOEH7KHUH-

fore, avoid having your child wear thick clothes under the belt.

• On long journeys, take regular breaks in order to give your child a chance to run

about and play.

• If using on the rear seat: Move the front seat far enough forward to ensure that

your child's feet will not knock against the backrest of the front seat (to prevent

the risk of injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people may

cause injury to other occupants in the vehicle. Therefore, please always ensure

that ...

QRORDGEHDULQJFRQWDFWSRLQWVDUHXVHGRWKHUWKDQWKRVHVSHFL¿HGLQWKHVH

instructions and those marked on the child seat.

• the backrests of the car seats are secured (for example, check that any fold-

down rear seat bench has snapped into place).

• all heavy or sharp-edged objects present in the vehicle (e.g. on the parcel shelf)

are held securely.

• all persons in the vehicle have their seatbelts fastened.

• the child seat is secured whenever it is in the vehicle, even if it is not carrying

a child.

WARNING! For your protection when handling the child seat:

• Never use the child seat in a free-standing position, not even for testing.

•

To avoid damage, ensure that the child seat is not jammed in between hard ob-

jects (car door, seat rails, etc.).

•

Keep the child seat in a safe place when not in use. Do not place heavy objects

on the seat and do not store directly next to heat sources or in direct sunlight.

CAUTION! To protect your vehicle:

• Certain car seat covers made from more sensitive materials (e.g. velour, leather,

etc.) may show wear marks after a child seat has been used. For optimum

protection of your car seat covers, we recommend using the BRITAX RÖMER

car seat protector from our range of accessories.

Child seat back

16. Press the safety catch at the centre of the group change switch 45, at the same

time moving it to the upper position for use with Group 2/3 (15-36 kg).

14. Close the two bottom press studs on the cover.

15. Close the two top press studs on the cover.

16. Close the two press studs on the upper cover of the headrest.

TAKING CARE OF THE HARNESS BUCKLE

To ensure the safety of your child, it is essential that the harness buckle continues

tofunction correctly. Harness buckle malfunctions are usually caused by dirt accumu-

lation or by external objects. Such malfunctions may be:

• When you press the red release button, the buckle clips are ejected only slowly.

• The buckle clips no longer engage (i.e. they pop out again when you try to push

them in).

• The buckle clips do not engage without an audible click.

• The buckle clips are dicult to push in (you feel a certain amount of resistance).

• It takes a lot of force to open the harness buckle.

Remedy

Rinse out the harness buckle so that it works perfectly again:

CLEANING THE HARNESS BUCKLE

1. Open the Velcro fastener on the crotch cushion 31 and remove it.

2. Remove the grey release plate 32 as described in Section “11. REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

3. Place the release plate 32 along with the harness buckle 20 in warm water

withsome washing-up liquid for at lease one hour.

4. Thoroughly rinse the harness buckle 20 and dry it completely.

5. Attach the grey release plate 32 as described in Section 11. “ REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

6. Attach the crotch cushion 31 .

CLEANING

CAUTION Please ensure that you use only original BRITAX replacement seat cov-

ers, as the seat cover is an integral part of the child seat and is important for correct

functioning of the system. Replacement seat covers are available from your dealer.

CAUTION! The child seat must not be used without its cover.

• The seat cover can be removed and washed with a mild detergent in a washing

machine with the “Delicates” programme (30 °C). Please follow the instructions

onthe washing label of the seat cover.

• The shoulder cushions can be removed and washed in lukewarm soapy water.

• The plastic parts, belts, and SecureGuard can be cleaned with soapy water.

Donotuse any aggressive cleaning agents (such as solvents).

Removing the shoulder cushions

1. Loosen the shoulder straps 08 as far as possible.

2. Open the shoulder cushions 19 by the Velcro fasteners at the side.

Child seat back

3. Bring the top tether 13 forward over the front of the seat.

4. Unhook the storage pouch 14 at the top.

5. Pull out the shoulder straps 08 a little so that you can see the rubber loops

oftheshoulder cushions 19 underneath.

6. Unhook the rubber loops from the plastic bars 41 on the shoulder strap height

adjuster 42 .

7. Pull the shoulder cushions 19 forwards out of the harness slots.

Reattaching the shoulder cushions

Simply follow the steps above in reverse order.

CAUTION The shoulder cushions 19 and belts must not be twisted or swapped

over. The shoulder straps 08 must be located under the black cover band 43

inthe shoulder cushions 19 .

Removing the cover

Headrest

1. Open the two press studs 33 at the belt slots.

2. Push the headrest of the child seat to the topmost position.

3. Pull the elastic band up from the edge of the tray and pull the tabs 34 out

ofthetwo slots in the seat pan.

4. Pull the cover edge out of the gap between the seat pan and the inlay cushion.

5. Unhook the rubber loops 35 under the headrest.

Seat pan

6. Undo the Velcro fastener on the crotch cushion 31 and remove it.

7. Open the four press studs 36 on the seat and back surface.

8. Push the harness buckle 20 or SecureGuard 26 through the cover slot.

9. Unhook the rubber loops 37 at the front under the seat surface and pull the tabs

38 out of the seat pan.

10. Pull the rubber loops carefully out of the gap around the belt guides 28 .

11. Pull the cover edge and tabs 39 out of the gap between the seat pan

andtheinlay cushion.

12. Pull the rubber loops 40 at the top of the back of the backrest out of the gap

inthe seat pan and and unhook them.

Reattaching the cover:

Simply follow the steps above in reverse order.

36 37

28 40

CAUTION! If the child seat is installed with Method A, always install the harness

buckle 20 correctly, and if installed with Method B, always install SecureGuard 26

correctly. Make sure that the release plate 45 is correctly attached.

CAUTION! Check that the straps are not twisted and are laid correctly through

the slots in the cover. The rear slot in the seat cover is provided for the harness buck-

le 20 and the front slot is provided for the SecureGuard 26. The slot at the front edge

of the seat is for the harness adjusting strap 22 .

2000034635 - 07/20

0506

25 28

11 26 25

1 cm

A properly adjusted headrest 07 ensures optimal protection

for your child on the child seat. Regularly check that the height

of the headrest 07 is suitable for the body height of your child:

The headrest 07 must be adjusted so that the shoulder straps

08 are at the same level as your child’s shoulders, or slightly

higher.

A correctly adjusted headrest 07 ensures that the diagonal

belt 11 is optimally positioned and gives your child optimum

protection. Regularly check that the height of the headrest 07

is suitable for the body height of your child:

The headrest 07 must be positioned so that two ﬁngers

can be inserted between the headrest 07 and your child's

shoulders.

To adjust the height of the headrest to ﬁt your child:

1. Press and hold the adjustment handle 10 on the back

ofthe headrest 07 .

2. The headrest 07 is now unlocked and can be moved

to the desired height. When you release the adjustment

handle 10 , the headrest 07 locks into place.

3. Place the child seat on the car seat.

4. Sit your child on the child seat and check the height.

Repeat this procedure until the headrest 07 is at thecor-

rect height.

5.3 Adjusting the headrest for Group II +III (15-36 kg)

1. If your vehicle is not ﬁtted with ISOFIX insertion aids

as standard, clamp the two insertion aids 02 (which

are supplied along with the seat*), with recess facing

upwards, into the two ISOFIX ﬁxing points 01 in your

vehicle.

TIP: The ISOFIX ﬁxing points are located between

theseat surface and the backrest of the car seat.

2. Move the headrest of the car seat to its topmost position.

3. Pull the grey handle 03 at the back of the child seat until

the ISOFIX locking arms 04 are fully extended.

4. On both sides of the ISOFIX locking arms, squeeze the

04 green locking button 05 and the red release button

06 together. This ensures that both hooks on the ISOFIX

locking arms 04 are open and ready to use.

* The insertion aids make it easier to install the child seat using the ISOFIX ﬁxing points and they

prevent damage to the car seat covers. If they are not being used, remove them and keep them

in a safe place. For vehicles with a folding backrest, the insertion aids need to be removed before

folding the backrest.

Any problems that occur are usually caused by dirt or external objects on the insertion aids and

onthe hook. Remove the dirt or external objects to resolve such problems.

5.1 Preparing ISOFIX

5.2 Adjusting the headrest for Group I (9-18 kg)

First please read the section describing the desired installation method in Section 6.

GROUP 2 (15-25 kg) &

GROUP 3 (22-36 kg)

With ISOFIT + car seat belt

GROUP 1 (9-18 kg)

With ISOFIX + Top Tether

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 5.1

“PREPARING ISOFIX”.

1.2 Follow the steps in Section 5.2 “ADJUSTING

THEHEADREST FOR GROUP I”.

2. PREPARING THE TOP TETHER

2.1 Unhook the snap-on hook 12 of the top tether 13

from the fastening on the back of the child seat.

2.2 Take the top tether 13 out of the pouch 14 and lay

itover the child seat.

TIP: Remove the outer rubber band only if the length

of the top tether 13 is not sucient for your vehicle

model.

2.3 Place the child seat in the direction of travel on an

approved car seat. Adjust the backrest angle of the

car seat so that the gap between the car seat and the

child seat is as small as possible.

2.4 Take the top tether 13 and press the metal tongue 15

away from the belt to extend it, and pull the top tether

13 at the snap-on hook 12 .

2.5 Guide the top tether 13 in the middle between the

bars of the headrest 07 , for integrated headrests on

the side closer to the top tether 13 anchorage point of

the vehicle.

3. FIXING THE TOP TETHER

Attach the snap-on hook 12 to the anchorage point

recommended in your vehicle's instruction manual.

CAUTION! Check that you are not using lug-

gagehooks instead of the top-tether anchorage

points.

Look for the following symbol in your vehicle:

4. FASTENING THE ISOFIX

4.1 Position the two ISOFIX locking arms 04 directly

infront of the two insertion aids 02 .

4.2 Push the two ISOFIX locking arms 04 into the insertion

aids 02 until the ISOFIX locking arms 04 engage

onboth sides with an audible click.

The green locking button DANGER! 05 must

bevisible on both sides indicating that the child seat

iscorrectly fastened.

5. PRESS THE CHILD SEAT BACKWARDS

Push the child safety seat ﬁrmly backwards as far as it will go.

6. CHECK FOR CORRECT FASTENING

Shake the child seat to check that it is securely fastened

and check the locking buttons 05 to make sure that the

two indicators are fully green.

7. TIGHTEN THE TOP TETHER

Tighten the top tether 13 , until the belt tension indicator

16 turns green and the top tether 13 is tight.

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 5.1

„PREPARINGISOFIX”.

1.2 Follow the steps in Section 5.3 “ADJUSTING

THEHEADREST FOR GROUP II+III”.

2. Place the child seat facing forward on an approved car

seat. Make sure that the backrest 30 is ﬂush with the back-

rest of the vehicle seat.

Tip: If the headrest of the car seat prevents the child seat

from being fastened properly, it should be removed (see

vehicle’s instruction manual). Secure the removed headrest

in a suitable place in the vehicle so that it will not be tossed

around.

3. FASTENING THE ISOFIX

3.1 Position the two ISOFIX locking arms 04 directly

infrontof the two insertion aids 02.

3.2 Push the two ISOFIX locking arms 04 into the inser-

tion aids 02 until the ISOFIX locking arms 04 engage

onboth sides with an audible click.

The green locking button DANGER! 05 must bevisi-

ble on both sides indicating that the child seat iscorrect-

ly fastened.

4. PRESS THE CHILD SEAT BACKWARDS

Push the child safety seat ﬁrmly backwards as far as it will go.

1. Follow the steps in Section 8 „ADJUSTING THE HEAD-

REST FOR GROUP II+III“ .

2. Place the child seat on the car seat. Ensure that the back-

rest 30 is ﬂat against the backrest of the car seat.

Tip: If the headrest of the car seat prevents the child

seat from being fastened properly, it should be removed

(see vehicle’s instruction manual). Secure the removed

headrest in a suitable place in the vehicle so that it will not

be tossed around.

3. Follow the steps in Section 8 “SECURING YOUR CHILD”.

5. CHECK FOR CORRECT FASTENING

Shake the child safety seat to ensure that it is securely fas-

tened, and check the locking buttons 05 again to ensure

that they are fully green.

6. Follow the steps in Section 8 “SECURING YOUR CHILD”.

Before every journey, for your child’s safety, check that ...

Źthe child seat is engaged on both sides with the ISOFIT locking arms in the ISOFIT

ﬁxing points and both locking buttons are fully green;

Źthe child seat is securely fastened;

Źthe lap belt passes through the bright red belt guides on both sides of the seat

cushion;

Źthe

lap belt passes through the bright red

SecureGuard;

Źthe diagonal belt on the car seat belt buckle side also passes through the bright

red belt guide on the seat cushion;

Źthe diagonal belt passes through the dark red belt holder at the headrest;

Źthe SICT side impact protection is correctly installed and functional;

Źthe diagonal belt runs diagonally backwards;

Źthe straps are tight and twisted;not

Źthe car seat belt buckle is placed in the bright red belt guide on the seat not

cushion.

Before every journey, for your child’s safety, check that ...

Źthe child seat is securely fastened;

Źthe lap belt

passes through the bright red belt guides

on both sides of the

seat cushion;

Źthe

lap belt

passes through the bright red

SecureGuard 26;

Źthe diagonal belt 11 on the side of the car seat belt buckle 27 also passes through

the bright red belt guide 28 on the seat cushion;

Źthe diagonal belt 11 passes through the dark red belt holder 29 at the headrest;

Źthe diagonal belt 11 runs diagonally backwards;

Źthe straps are tight and twisted;not

Źthe SICT side impact protection 17 is correctly installed and functional;

Źthe car seat belt buckle 27 is placed in the bright red belt guide not 28 on the seat

cushion.

1. Turn the SICT

17 anti-clockwise (on the side nearer

thevehicle door) until there is a gap of 5 mm between

it and the vehicle door or until it is fully unscrewed.

Pullout the car seat belt, pass it in front of your child

and into the car seat belt buckle 27.

Check that the car seat belt is not twist-DANGER!

ed, otherwise the full protective action of the restraint

system will be impaired.

2. Insert the buckle clip in the car seat belt buckle 27 until

there is an audible click.

3. Place the diagonal belt 11 and lap belt 25 on

the side of the car seat belt buckle 27 in the bright

redbelt guide 28 on the seat cushion.

The seat belt buckle DANGER! 27 must

notbeplaced near the bright red belt guide 28 .

4. Also place the lap belt 25 on the other side

oftheseatcushion in the light red belt guide 28 .

The lap belt DANGER! 25 must be placed as

lowaspossible over your child's hips on both sides.

5. Insert the lap belt 25 in the bright red SecureGuard 26 .

DANGER! Do not insert the diagonal belt 11 in the

bright red SecureGuard 26 .

6. Place the diagonal belt 11 in the dark red belt holder 29

atthe headrest 07 until it is fully in the belt holder 29

without twisting.

If the backrest Tip: 30 is covering the dark red belt

holder 29, you can adjust the headrest 07 upwards.

Thediagonal belt 11 can now be easily inserted. You

cannow adjust the headrest 07 back to the correct height.

7. the diagonal belt Make sure that 11 passes over

thecollarbone of your child, not the neck, and that the

button on the dark red belt holder is 29 fully closed.

You can adjust the height of the headrest Tip: 07

again in the vehicle.

DANGER! The diagonal belt 11 must run diagonally

backwards. You can adjust the position of the belt with

the adjustable belt deﬂector of the vehicle.

The diagonal belt DANGER! 11 must never run

forwards towards the belt deﬂector on the vehicle.

Inthiscase, use the child seat on the back seat only.

8. Tighten the car seat belt by pulling on the diagonal belt 11 .

9. Follow the safety instructions for the installation method

concerned.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 9

"REMOVING THE CHILD SEAT ."

The

ADVANSAFIX IV R

is not permanently installed in the vehicle. It is simply secured

along with your child by the vehicle's 3-point seat belt.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 9

“REMOVING THE CHILD SEAT”.

ŹThe shoulder straps 08 must be adjusted so that they

arehorizontal or just above your child’s shoulders.

ŹThe shoulder straps 08 must not be passed behind the

child’s back, or placed level with or above the child’s ears.

The shoulder straps are adjusted as follows:

1. Loosen the 5-point harness 09 on the child seat as far

aspossible.

2. Press and hold the adjustment handle 10 on the back

ofthe headres t 07 .

3. The unlocked headrest 07 can now be moved to the

desired height. When you release the adjustment handle

10 , the headrest 07 locks into place.

9. LOOSEN THE SHOULDER STRAPS

To loosen the shoulder straps, press the adjustment button

18 while at the same time pulling both shoulder straps 08

forward.

Do not pull the shoulder cushions CAUTION! 19 .

10. OPEN THE HARNESS BUCKLE

To open the harness buckle 20 press the red button

onthe buckle.

11. SET THE CHILD IN THE CHILD SEAT

Place your child in the child seat.

Check that the harness buckle 20 is facing forwards.

12. PLACE THE SHOULDER STRAPS

Pass the shoulder straps 08 over your child’s shoulders.

Do not twist or swap the shoulder WARNING!

straps, as this will remove their protective function.

13. FASTENING THE HARNESS BUCKLE

Take the two buckle clips 21 and hold them together

before inserting them in the harness buckle 20 – they must

make an audible click when inserted.

14. TIGHTENING THE ADJUSTMENT STRAP

Pull the adjustment strap 22 until the strap lies ﬂat

andsnug around your child’s body.

The hip belts must be positioned WARNING!

aslowas possible across your child's hips.

Before each journey, in order to ensure your child’s safety, make

sure that ...

Źthe child seat is engaged on both sides with the ISOFIT locking arms 04

intheISOFIX ﬁxing points 01 and that both locking buttons 05 are fully green;

Źthe child seat is securely fastened;

Źthe top tether 13 is tight over the backrest of the car seat and the belt tension

indicator 16 is green;

Źthe child seat belts ﬁt snugly around the child’s body without causing constriction;

Źthe shoulder straps 08 are correctly adjusted and are twisted;not

Źthe shoulder cushions 19 are in the correct position for your child’s body;

Źboth buckle clips 21 are fully engaged in the harness buckle 20 ;

Źthe SICT side impact protection 17 is correctly installed and functional.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 9

"REMOVING THE CHILD SEAT".

The seat pan of the

ADVANSAFIX IV R

KDVWKUHHGLႇHUHQWDQJOHVRIWLOW

To adjust the seat angle:

Pull the adjustment handle 23 forwards and push/slide

the seat pan 24 into the desired position.

DANGER! The seat pan 24 PXVWEH¿UPO\HQJDJHG

whatever the position. Pull on the seat pan 24 to check

that it has engaged.

TIP: You can adjust the tilt angle of the child seat 24

even while your child is sitting on it.

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, waste incineration

Plastic parts To be placed in the corresponding container

according to the labels

Metal parts Container for metals

Belt straps Container for polyester

Buckle and clip Residual waste

DANGER!

If your child tries to open the car seat belt buckle 27 or insert the

diagonal belt 11 in the bright red SecureGuard 26 , stop your vehicle immedi-

ately, or as soon as possible. Check that the child seat is correctly fastened and

that your child is correctly secured. Explain to your child the dangers caused by

such actions.

DANGER! If your child tries to open the car seat belt buckle 27 or insert the di-

agonal belt 11 in the bright red SecureGuard 26, stop the vehicle immediately, oras

soon as possible. Check that the child safety seat is correctly fastened and that your

child is correctly secured. Explain to your child the dangers caused by such actions.

DANGER! Remove the child seat from the vehicle. Never carry the child seat

inthe car if it is not fastened properly.

A) GROUP 1 (ISOFIX & TOP TETHER)

1. Loosen the top tether 13 by pushing the metal tongue 15

away from the belt.

2. Release the snap-on hook 12 from the anchorage point in the vehicle and lay

the top tether 13 to the front over the child seat.

3. Loosen the ISOFIX fastening on both sides by squeezing the green locking

button 05 and red release button 06 together.

4. Pull the seat forward and store the top tether 13 in the storage pouch 14

and attach the snap-on hook of the top tether 13 to the fastening on the back

of the child seat.

5. Move the ISOFIX locking arms 04 back into the seat pan 24 .

B) GROUP 2/3 (ISOFIT & CAR SEAT BELT / CAR SEAT BELT)

1. Press the release button on your car seat buckle

2. Open the dark red belt holder 29 by pressing the button on the belt holder

backwards and pull out the diagonal belt 11.

Only for installation method with ISOFIT:

3. To release the ISOFIT fastening, squeeze the green locking button

and red release button 06 WRJHWKHU¿UVWRQRQHVLGHWKHQRQWKHRWKHU

4. Move the ISOFIX locking arms 04 back into the seat pan 24 .

GROUP 2 (15-25 kg) &

GROUP 3 (22-36 kg)

With car seat belt

8. ADJUSTING THE SICT

Turn the SICT 17 anti-clockwise (on the side nearer

thevehicle door) until there is a gap of 5 mm between

itand the vehicle door, or until it is fully unscrewed.

5. PREPARATORY STEPS 6. INSTALLATION & USE

7. ADJUSTING THE SEAT ANGLE

8. SECURING YOUR CHILD

9. REMOVING THE CHILD SEAT

10. DISPOSAL

Produktspezifikationen

Marke:	Britax-Römer
Kategorie:	Autositz
Modell:	Advansafix IV R

Brauchst du Hilfe?

Wenn Sie Hilfe mit Britax-Römer Advansafix IV R benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Autositz Britax-Römer

Britax-Römer BABY-SAFE 2 i-SIZE Bedienungsanleitung

25 August 2024

Britax-Römer KIDFIX XP SICT Bedienungsanleitung

24 August 2024

Britax-Römer FIRST CLASS PLUS - 2017 Bedienungsanleitung

24 August 2024

Britax-Römer BABY-SAFE ISOFIX BASE 2014 Bedienungsanleitung

24 August 2024

Britax-Römer VERSAFIX Bedienungsanleitung

24 August 2024

Britax-Römer PRIMO BASE Bedienungsanleitung

24 August 2024

Britax-Römer KING II - ATS - LS Bedienungsanleitung

24 August 2024

Britax-Römer KIDFIX SL SICT Bedienungsanleitung

24 August 2024

Britax-Römer DUALFIX 3 i-SIZE Bedienungsanleitung

23 August 2024

Britax-Römer ADVANSAFIX Z-LINE Bedienungsanleitung

23 August 2024

Bedienungsanleitung Autositz

Neueste Bedienungsanleitung für -Kategorien-

Römer EVOLVA 1-2-3 plus Bedienungsanleitung

14 Oktober 2024

Lorelli Jupiter Bedienungsanleitung

5 Oktober 2024

Joie i-Prodigi Bedienungsanleitung

30 September 2024

Römer BABY-SAFE plus SHR II Bedienungsanleitung

27 September 2024

Cosatto Zoomi Bedienungsanleitung

24 September 2024

Cosatto Axkid Minikid 4 Bedienungsanleitung

24 September 2024

Cosatto All in All Ultra Rotate i-Size Bedienungsanleitung

24 September 2024

Cosatto All in All 360 Rotate i-Size Bedienungsanleitung

24 September 2024

Cosatto Acorn 2 i-Size Bedienungsanleitung

24 September 2024

Xadventure Junior Isofix Bedienungsanleitung

23 September 2024