Bosch HomeProfessional WTY88701AU Bedienungsanleitung

Bosch Wäschetrockner HomeProfessional WTY88701AU

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Bosch HomeProfessional WTY88701AU (6 Seiten) in der Kategorie Wäschetrockner. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/6
1
Environmentally-responsible disposal
– Dispose of packaging in an environmentally-responsible manner.
This appliance is labelled in accordance with European Directive 2012/19/EU concerning
used electrical and electronic appliances (waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and recycling of used appliances as
applicable throughout the EU.
Installation
– Scope of delivery: dryer, instruction manual, installation and maintenance instructions,
jug and woollens basket (depending on the model).
– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
– Ensure that the appliance is installed on a clean,
level and firm surface.
– The appliance plug must always be accessible.
– Do not obstruct the air inlet on the dryer.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet
and a spirit level.
– Do not remove the threaded feet under any
circumstances.
For mains connection, see Safety instructions page 13.a
– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (apage 4) must be the same.
The connected load and necessary fuse protection are specified on the rating plate.
Frost protection / Transport
Preparation
1. Empty the condensation container .aPage 4
2. Select any programme using the programme selector.
3. Press the ( /Pause) button condensation water is pumped into the container.$ Start a
4. Wait 5 minutes and then empty the condensation container again.
5. Switch the dryer off using the programme selector.
6. Transport the dryer in a vertical upright position.
7. Following transportation, do not use the dryer for two hours.
The dryer contains residual water.
This can flow out if the dryer is tilted.
The refresher tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.
1.
Make sure that the air
inlet remains unobstructed
Clean and level
D
o no
t
se
t
up
th
e
d
ryer
b
e
hi
n
d
a
d
oor or s
lidi
ng
door, as this may obstruct the dryer door or prevent
it from opening. This will prevent children from
locking themselves in, thereby putting their lives at
risk.
Take all accessory parts out of the drum.
The drum must be empty.
2.
2
Care and cleaning
Dryer housing, control panel
Remove detergent residues immediately.
Wipe with a soft, damp cloth.
Do not clean with a water jet.
During drying, water may accumulate between the window and the seal.
Moisture sensor
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure how damp the laundry is.
A thin layer of limescale may build up on the moisture sensors after
prolonged use.
This must be removed regularly.
1. Open the door and clean the moisture sensors with a damp
sponge that has a rough surface.
Do not use steel wool or abrasive materials.
Cover for steam nozzle in the drum (depending on the model)
After prolonged operation, limescale and fluff may accumulate on the cover of the steam
nozzle. Clean regularly:
1. Open the door and remove the cover with a screwdriver.
Clean the cover under running water.
2. Push and click the cover back in place.
Clean the filter in the refresher tank if it is dirty (depending on the model)
Regularly clean the filter under running water a This prevents stubborn deposits/dirt from
building up.
1. Remove the condensation container.
2. Remove the filter and clean it under running water.
3. Re-insert the filter and push in the condensation container until it
locks into place.
3
Care and cleaning
Heat exchanger
The dryer's heat exchanger is automatically cleaned during drying and Heat exchanger is
being rinsed is displayed in the display panel. Do not pull out the condensation container
during this cleaning process.
Filter in the condensation container
The filter is cleaned automatically when the condensation container is emptied.
However, the filter should still be cleaned regularly under running water This prevents a
stubborn deposits/dirt from building up.
If the condensation drain is installed (depending on the model), it is not necessary to clean
the filter separate .aInstructions for the condensation drain
1. Pull out the condensation container.
2. Pull the filter out of its snap-in lock.
3. Clean the filter under running water or in the dishwasher.
4. Refit the filter.
5. Push the condensation container back in until it locks into place.
Only operate the dryer with the filter inserted.
4
After-sales service
If you cannot rectify the fault yourself instruction manual: aWhat to do if...
page 12, please contact our after-sales service. We will always find an appropriate solution
and avoid unnecessary visits by engineers.
You can find the contact details for your nearest after-sales service on page 12 of the
instruction manual or in the after-sales service directory.
Please give the after-sales service the product number (E no.) and the production number
(FD) of the appliance.
Product number Production number
You can find this information:
inside the door* / in the opened service flap*
and on the rear of the appliance.
*depending on the model
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest
assured that the repair will be carried out by trained service technicians using original spare
parts.
Optional accessories (order from the after-sales service using the order number, depending on model)
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. The dryer must be fastened to the washing machine using this connection set.
WTZ 11400: with pull-out worktop.
Wollens basket
For drying individual wollen fabrics, sports shoes and soft toys (see separate instructions for
“Woollens basket”).
Platform
For easier loading and unloading. The basket contained in the drawer can be used
to carry the laundry.
Technical data
Dimensions (DxWxH) 60 x 60 x 85 cm (adjustable height)
Weight approx. 57 kg
Max. capacity* 8 kg / 9 kg
Condensation container 4.6 l
Refresher tank approx. 0.4 l
Connection voltage 220-240 V
Connected load max. 1000 W (for models with a max. 1600 W steam
function)
Fuse protection 10 A
Ambient temperature 5 - 35 °C
Product number
Production number Inside of door
The rating plate can be found on the back of the dryer.
*depending on the model operating instructions: Programme overview, page 7a
WTZ
20410
WMZ
20600
WMZ
20500
5
Reversing the door
1 6
22.
1.
7
3 8
4 9
53.
1.
2.
10
6 11
9406 / 9000695672
*695672*
6
Reversing the door
11 16
12 17
13 18 1.
3.
2.
14 19
15 20 1.
2.
16 21
7
Reversing the door
21 26
22
1.
2.
27
23
1.
2.
3.
28
24
1.
2.
29
25 1. 2.
26
Dryer
Contents Page
ʋEnvironmentally-friendly disposal . . . . . . 1
ʋInstallation . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋFrost protection / Transport. . . . . . . . . . . 1
ʋCare and cleaning . . . . . . . . . . . . . . . 2/3
ʋAfter-sales service . . . . . . . . . . . . . . . . . . 4
ʋOptional accessories . . . . . . . . . . . . . . . . 4
ʋTechnical data . . . . . . . . . . . . . . . . . . . . 4
ʋReversing the door . . . . . . . . . . . . . . . 5/7
Installation and
maintenance
instructions
Read these instructions before operating the dryer.
You must also observe the separate instruction manual.
Keep all the documents in a safe place for future reference, or to
pass on to the next owner.
en
1
Environmentally-responsible disposal
– Dispose of packaging in an environmentally-responsible manner.
This appliance is labelled in accordance with European Directive 2012/19/EU concerning
used electrical and electronic appliances (waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and recycling of used appliances as
applicable throughout the EU.
Installation
– Scope of delivery: dryer, instruction manual, installation and maintenance instructions,
jug and woollens basket (depending on the model).
– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
– Ensure that the appliance is installed on a clean,
level and firm surface.
– The appliance plug must always be accessible.
– Do not obstruct the air inlet on the dryer.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet
and a spirit level.
– Do not remove the threaded feet under any
circumstances.
For mains connection, see Safety instructions page 13.a
– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (apage 4) must be the same.
The connected load and necessary fuse protection are specified on the rating plate.
Frost protection / Transport
Preparation
1. Empty the condensation container .aPage 4
2. Select any programme using the programme selector.
3. Press the ( /Pause) button condensation water is pumped into the container.$ Start a
4. Wait 5 minutes and then empty the condensation container again.
5. Switch the dryer off using the programme selector.
6. Transport the dryer in a vertical upright position.
7. Following transportation, do not use the dryer for two hours.
The dryer contains residual water.
This can flow out if the dryer is tilted.
The refresher tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.
1.
Make sure that the air
inlet remains unobstructed
Clean and level
D
o no
t
se
t
up
th
e
d
ryer
b
e
hi
n
d
a
d
oor or s
lidi
ng
door, as this may obstruct the dryer door or prevent
it from opening. This will prevent children from
locking themselves in, thereby putting their lives at
risk.
Take all accessory parts out of the drum.
The drum must be empty.
2.
2
Care and cleaning
Dryer housing, control panel
Remove detergent residues immediately.
Wipe with a soft, damp cloth.
Do not clean with a water jet.
During drying, water may accumulate between the window and the seal.
Moisture sensor
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure how damp the laundry is.
A thin layer of limescale may build up on the moisture sensors after
prolonged use.
This must be removed regularly.
1. Open the door and clean the moisture sensors with a damp
sponge that has a rough surface.
Do not use steel wool or abrasive materials.
Cover for steam nozzle in the drum (depending on the model)
After prolonged operation, limescale and fluff may accumulate on the cover of the steam
nozzle. Clean regularly:
1. Open the door and remove the cover with a screwdriver.
Clean the cover under running water.
2. Push and click the cover back in place.
Clean the filter in the refresher tank if it is dirty (depending on the model)
Regularly clean the filter under running water This prevents stubborn deposits/dirt from a
building up.
1. Remove the condensation container.
2. Remove the filter and clean it under running water.
3. Re-insert the filter and push in the condensation container until it
locks into place.

Produktspezifikationen

Marke: Bosch
Kategorie: Wäschetrockner
Modell: HomeProfessional WTY88701AU

Brauchst du Hilfe?

Wenn Sie Hilfe mit Bosch HomeProfessional WTY88701AU benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Wäschetrockner Bosch

Bosch

Bosch WTA4000 Bedienungsanleitung

16 Oktober 2024
Bosch

Bosch WTH8300CNL Bedienungsanleitung

15 Oktober 2024
Bosch

Bosch WTW85469AU Bedienungsanleitung

13 Oktober 2024
Bosch

Bosch WTW85231GB Bedienungsanleitung

8 Oktober 2024
Bosch

Bosch Serie 4 WTH85201NL Bedienungsanleitung

4 Oktober 2024
Bosch

Bosch WPG23108GB Bedienungsanleitung

29 September 2024
Bosch

Bosch WTH83204FG Bedienungsanleitung

27 September 2024
Bosch

Bosch WTH85200FG Bedienungsanleitung

23 September 2024
Bosch

Bosch WTR85V18IT Bedienungsanleitung

15 September 2024
Bosch

Bosch WTR85T71EX Bedienungsanleitung

5 September 2024

Bedienungsanleitung Wäschetrockner

Neueste Bedienungsanleitung für -Kategorien-

GE

GE Profile PFD95GSPTDS Bedienungsanleitung

16 Oktober 2024
Maytag

Maytag MGD7100DC Maxima Bedienungsanleitung

16 Oktober 2024
Bauknecht

Bauknecht TRKP 7950 Bedienungsanleitung

16 Oktober 2024
Hoover

Hoover DX C9DKG-80 Bedienungsanleitung

16 Oktober 2024
Teka

Teka THPD80 Bedienungsanleitung

16 Oktober 2024
BEKO

BEKO B3T41242 Bedienungsanleitung

16 Oktober 2024
BEKO

BEKO BM5T49243W Bedienungsanleitung

16 Oktober 2024
BEKO

BEKO B3T67110 Bedienungsanleitung

16 Oktober 2024
BEKO

BEKO BM3T48249W Bedienungsanleitung

16 Oktober 2024
Whirlpool

Whirlpool FFT M11 8X3BY EE Bedienungsanleitung

15 Oktober 2024