Behringer CT100 Bedienungsanleitung

Behringer niet gecategoriseerd CT100

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Behringer CT100 (62 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/62
User Manual
CABLE TESTER CT100
Professional 6-in-1 Cable Tester
V 7.0
2CABLE TE STER CT100
1. Introduction
Congratulations! With the CT100, you have purchased an indispensable
tool that enables you to easily check the most common cables used
by musicians and sound engineers. Faulty cables are a common cause
of failure in live and studio situations. This microprocessor-controlled
device was designed to ensure fast, reliable problem location. Various
test modes and the included belt clip add to its exibility.
2. Cable Tester Mode
◊
◊
◊
◊ ◊ Move the ON switch to the CABLE TESTER position.
Insert one end of your cable into any OUT jack of the CT100. Connect
the other end of the cable to any IN jack. The LEDs will indicate
which input pins are connected to each output pin. Additionally, the
GROUNDED SHIELD LED indicates whether a XLR OUT jack’s shield is
connected to the pin 1/sleeve signal.
2.1 How to test intermittent connections
The following method allows you to detect intermittent connections
caused by wire breaks or faulty solder points. While in CABLE TESTER
MODE, press RESET to store the current cable-wiring display and to clear
the INTERMITTENT LEDs. Move the cable vigorously in all directions
and watch the LEDs. Any change in wiring or break in the signal ow
will cause the LED of the corresponding input pin to light up. TheLED
will stay lit until RESET is pressed again, assuring detection of even the
shortest breaks in the signal ow. It is a good idea to repeat the test
after resetting the LEDs to double-check the initial results.
3. Installed Cable Tester Mode
This mode enables you to test cables in xed installations or situations
that don’t allow you to connect both ends of the cable to the CT100.
◊
◊
◊
◊ ◊ Hold down the RESET button while moving the ON switch to
the CABLE TESTER position. The ON LED will blink to indicate
that the CT100 is in INSTALLED CABLE TESTER MODE.
3
CABLE TE STER CT100
To test a cable for short circuits, connect one end of the cable to the
appropriate OUT jack of the CT100. The display works as in CABLE
TESTER MODE (see chapter 2). However, it now indicates connections
between out pins. If no LEDs light, the cable is free of short circuits.
3.1 Continuity check in Installed
Cable Tester Mode
For a continuity check, connect a shorting jack (a jack in which pins
are short-circuited to one another) to the other end of the cable.
If there are no breaks in the signal ow, the display will show the
corresponding pins as being shorted to each other. If the display
indicates no short circuit, there is a break in the signal ow.
◊
◊
◊
◊ ◊ The testing of intermittent connections works exactly as in
CABLE TESTER MODE (see chapter 2.1).
◊
◊
◊
◊ ◊ INSTALLED CABLE TESTER MODE will not indicate connections
between out and in pins. This is done in CABLE TESTER MODE
(see chapter 2).
4. Test Tone Mode
◊
◊
◊
◊ ◊ Move the ON switch to the position TEST TONE.
◊
◊
◊
◊ ◊ Do not use the TEST TONE MODE for MIDI cables!
TEST TONE MODE may be used to check signal ow and to facilitate
level adjustments. It routes a test tone to the “+ pin” (pin 2/tip) of
all OUT jacks. Use the TEST TONE LEVEL switch to choose between +4
dBu, -10 dBV, or -50 dBV mic level. Please note that this mode is not
intended to work as a voltage standard and that battery voltage will
aect the test tone output level.
4.1 Selection between 1 kHz and 440 Hz
While in TEST TONE MODE, pressing RESET toggles between 1 kHz and
440 Hz. The TEST TONE LED indicates the selected frequency:
On = 1 kHz, O = 440 Hz.

Produktspezifikationen

Marke: Behringer
Kategorie: niet gecategoriseerd
Modell: CT100

Brauchst du Hilfe?

Wenn Sie Hilfe mit Behringer CT100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung niet gecategoriseerd Behringer

Behringer

Behringer PSU4-UL Bedienungsanleitung

6 Oktober 2024
Behringer

Behringer S32 Bedienungsanleitung

4 Oktober 2024
Behringer

Behringer PSU3-KR Bedienungsanleitung

22 September 2024
Behringer

Behringer MOTÖR 49 Bedienungsanleitung

18 September 2024
Behringer

Behringer PSU4-EU Bedienungsanleitung

17 September 2024
Behringer

Behringer Rhythm Designer RD-9 Bedienungsanleitung

15 September 2024
Behringer

Behringer S16 Bedienungsanleitung

12 September 2024
Behringer

Behringer Eurolight LC2412 Bedienungsanleitung

9 September 2024
Behringer

Behringer UltraLink ULM300USB Bedienungsanleitung

5 September 2024
Behringer

Behringer RD-6-SB -Translucent Bedienungsanleitung

22 August 2024

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-

BEKO

BEKO BHCA67841BBHSI Bedienungsanleitung

7 Oktober 2024
ETNA

ETNA AW9075RVS Bedienungsanleitung

7 Oktober 2024
Megger

Megger MPCC230 Bedienungsanleitung

7 Oktober 2024
NABO

NABO FK 2755 Bedienungsanleitung

7 Oktober 2024
BEKO

BEKO FSE67300XCS Bedienungsanleitung

7 Oktober 2024
Biltema

Biltema 65-279 Bedienungsanleitung

7 Oktober 2024
Hauck

Hauck Nerf Battle Racer Bedienungsanleitung

7 Oktober 2024
Shimano

Shimano ST-2400-R Bedienungsanleitung

7 Oktober 2024
IFM

IFM AC5291 Bedienungsanleitung

7 Oktober 2024
GE

GE ZXR7510C Bedienungsanleitung

7 Oktober 2024