Baumatic BGG60 Bedienungsanleitung

Baumatic Ofen BGG60

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Baumatic BGG60 (32 Seiten) in der Kategorie Ofen. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/32
el 1
BGG30 / BGG32 /
BGG60 / BGG64 / BGG70
Gas hobs
User Manual for your Baumatic
BGG30 / BGG32
30 cm Burner gas hob
BGG60 / BGG64
60 cm 4 Burner gas hob
BGG70
70 cm 5 Burner gas hob
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 09/11/12
2
3
Contents
Enviro
nmental note
4
Important safety information 5 – 7
Specifications 8 – 13
BGG30 / BGG32 8
BGG60 / BGG64 9
BGG70 10
Electrical details 11
Gas details 11
Gas hob surface layout 12 - 13
Using the gas hob 13 - 15
Before first use 13
Switching the hob on 13 - 14
Automatic ignition with flame failure device 14
Energy saving tips 15
Cleaning 16 - 17
Cleaning the hob top 16
After each use 16
Cleaning the hob burners 16 - 17
Maintaining the cast iron pan stands 17
Installation 17 - 28
Positioning 18 - 19
Unpacking the appliance 19
Installing the appliance 19 – 22
Gas connection 22
Ventilation requirements 23
Gas Safety (Installation and Use) Regulations 24
Gas Adjustment (Conversion to LPG) 25
Minimum flow adjustment for hob gas taps 26
Gas tap maintenance 27
Electrical connection 28
Replacing the mains supply cable 28
My appliance isn’t working correctly 29
Baumatic consumables 30
Contact details 31
Environmental note
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
all packaging material with due regard for the
environment.
o Please discard
4
6
hild Safety
ce at any time. During and after use, all
surfaces will be hot.
se ensure that they are kept under close supervision
at all times.
uld only be allowed to utilise the appliance
when supervised.
eneral Safety
e installed and connected by a
GASSAFE registered installer.
uild the appliance into, meet with the relevant
standards.
uring use
hob surface when it
is delivered should be removed before use.
the appliance, otherwise
there is a risk of burns being caused.
t with the hob surface when it is hot or any hot
cookware.
ng with fat and oil the appliance should
not be left unattended.
sure that all of the cooking zones are switched off after
use.
C
o Baumatic strongly recommend that babies and young children
are prevented from being near to the appliance and not allowed
to touch the applian
o If it is necessary for younger family members to be in the
kitchen, plea
o Older children sho
G
o The appliance should only b
o Care should be taken to ensure that the units and work surfaces
that you b
D
o Any lm or stickers that are present on the
o Care should be used when utilising
o You should not allow the electrical connection cables to come
into contac
o If fat and oil overheats, then it can ignite extremely quickly. For
this reason, when cooki
o Make
8 8
pecifications S
BGG30 /
Width: 268 mm
Product specifications (B
burner
1 x 1.00 kW auxiliary burner
s
GG30 only)
BGG32
Product dimensions: Aperture dimensions:
Depth: 520 mm Depth: 490 mm
Width: 300 mm
Height: 40 mm
GG30):
o 1 x 3.80 kW triple crown (wok)
Product specifications (BGG32):
o 1 x 3.00 kW rapid burner
o
o Front control operation
Automatic ignition o
o Heavy duty cast iron pan stands
o Flame failure safety device on each burner
Standard accessories:
o LPG conversion jet
Optional extra:
o Wok stand (B
9
GG
Width: 560 mm
):
urner
o 1 x 1.00 kW auxiliary burner
device on each burner
sion jets
o
B 60 / BGG64
Product dimensions: Aperture dimensions:
Depth: 480 mm Depth: 510 mm
idth: 600 mm W
Height: 40 mm
Product specifications (BGG60
o 1 x 3.00 kW rapid burner
2 x 1.75 kW semi-rapid burnerso
o 1 x 1.00 kW auxiliary burner
Product specifications (BGG64):
)o 1 x 3.80 kW triple crown (wok
2 x 1.75 kW semi-rapid burners
b
o
o Front control operation
o Automatic ignition
Heavy duty cast iron pan stands o
o Flame failure safety
Standard accessories:
o LPG conver
Optional extra:
Wok stand (BGG64 only)
BGG70
10
Width: 560 mm
urner
rner
ty device on each burner
ion jets
o Wok stand
Product dimensions: Aperture dimensions:
Depth: 480 mm Depth: 510 mm
idth: 700 mm W
Height: 40 mm
Product specifications:
o 1 x 3.80 kW triple crown (wok) b
o 1 x 3.00 kW rapid burner
2 x 1.75 kW semi-rapid burnerso
o 1 x 1.00 kW auxiliary bu
o Front control operation
o Automatic ignition
Heavy duty cast iron pan stands o
o Flame failure safe
Standard accessories:
o LPG convers
Optional extra:
11
Rated Voltage: / 60 Hz
ole switched fused outlet with
ax Rated Inputs: 0.0008 kW
y Lead: 3 core x 0.75mm² (Type RR-F <HAR> marked)
onn tion:
bar)
Alternative LPG G30 (28-30/37 mbar)
ur hob is located on
e underneath of the appliance. Therefore it is a good idea to record
pliance.
ate of Purchase ……………………………….
Electrical details
220 - 240 Vac 50
Supply Connection: 3 A (double p
3mm contact gap)
M
Mains Suppl
Gas details
C ec Rp ½ (ISO R7)
Type: Natural Gas (20 m
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of yo
th
this information before you install your ap
Model Number ……………………………….
Serial Number ……………………………….
D
12
ace layout
= 3.80 kW triple crown (wok) burner
= Control panel
ary burner
= 3.00 kW rapid burner
= Control panel
er
rapid burner
= 3.00 kW rapid burner
= Control panel
Gas hob surf
BGG30
A
B
BGG32
A = 1.00 kW auxili
B
C
BGG60
A = 1.00 kW auxiliary burn
B = 1.75 kW semi-
C
D
BGG64
A = 1.00 kW auxiliary burner
B = 1.75 kW semi-rapid burner
C = 3.80 kW triple crown (wok) burner
D = Control panel
BGG70
13
-rapid burner
= 3.00 kW rapid burner
= 3.80 kW triple crown (wok) burner
= Control panel
A = 1.00 kW auxiliary burner
B = 1.75 kW semi
C
D
E
Using the gas hob
Before
ou should clean the hob surface.
(Please see the “Cleaning and maintenance” section).
hob on
bols will appear on the control panel, next to each
control knob:
first use
IMPORTANT: Y
Switching the
The following sym
setting
nimum setting
= gas off
Large flame: maximum
Small flame: mi
o The minimum setting is at the end of the anti-clockwise rotation of
the control knob.
14
position.
The symbol on the control panel, next to the control knob will
he appliance is fitted with a flame failure safety device on each
igned to stop the flow of gas to the burner head in
e event of the flame going out.
aximum position.
o After this 20 second interval, turn the control knob to your
f position.
o In case of power failure, the burners can be lit by carefully using
a match.
o All operation positions must be selected between the maximum and
minimum
o Never select a knob position between the maximum and off
position.
o
indicate which gas burner it operates.
Automatic ignition with flame failure safety device
T
burner, which is des
th
To ignite a burner:
o Press in the control knob of the burner that you wish to light and
turn it anti-clockwise to the m
o If you keep the control knob depressed, the automatic ignition
for the burner will operate.
o You should hold down the control knob for 20 seconds after the
flame on the burner has lit.
required setting between the maximum and minimum setting
symbols.
o To switch the burner off, turn the control knob fully clockwise to
the gas of
15
Energy saving tips
NPA S BURNERS
Minimum
diametre
M
d
aximum
iametre
Wok 220 mm 260 mm
Rapid 180 mm 220 mm
Semi-rapid
120 mm 200 mm
Auxiliary 80 mm 160 mm
o The diametre of th spond to that
of the burner.
extend beyond the diametre of the
pan.
o Use flat bottomed pans only.
keep a lid on the pan whilst cooking.
s centrally over the hob burners and
osition them so that the handles cannot get accidentally caught or
nocked off. You should also make sure that the handle is not over one
f the other hob burner flames.
e bottom of the pan should corre
o The burner flame must never
o When possible,
o Cook vegetables with as little water as possible, to reduce
cooking times.
IMPORTANT: Always place pan
p
k
o
17
o IMPORTANT: Make sure that you reassemble the burners in the
o IMPORTANT: Make sure that the hob surface and pan stands
t, damp cloth that has been
put into warm soapy water. The cloth should be wrung out after
ands, we
would recommend that you rub a small amount of olive oil into
the pan stands, after you have finished cleaning them.
o
original way.
Maintaining the cast iron pan stands
have cooled before you attempt to touch them.
o Wipe the pan stands over with a sof
being taken out of the soapy water.
o Using a paper towel, thoroughly dry the pan stands.
o To maintain the appearance of the cast iron pan st
Installati n
The installation must be carried out by a GASSAFE
egistered installer, in accordance with the current
version of the following.
Building Standards (Issued by the Scottish Development
o Installation of Domestic Gas Cooking Appliances (if necessary,
lation for Gas Appliances
o Baumatic Ltd Installation Instructions
r
o Gas Safety Regulations (Installation & Use)
o Building Regulations (issued by the Department of Environment)
o
Department)
o IEE Wiring Regulations
o Electricity at Work Regulations BS 6172
BS 5482 Installation of Domestic LPG Appliances)
o BS 5440 Installation of Flues and Venti
18
i
rature rise of 85°C above the ambient
temperature of the room it is located in, during
d:
BGG32)
600 mm (BGG60 / BGG64)
d in a kitchen, a kitchen diner or a bed
sitting room. IMPORTANT: The appliance must not be installed in a
herefore is to be built into a
itchen unit (depending on size) or 600mm worktop, providing the
The edges of the hob must be a minimum distance of 55 mm from
mm between the highest point of the hob surface (including the
burners) and the underside of any horizontal surface directly above
Position
ng
The adjacent furniture must be able to withstand a
minimum tempe
periods of use.
Minimum width of cooker hoo
* 300 mm (BGG30 /
*
* 700 mm (BGG70)
o This appliance can be locate
bathroom or shower room.
This appliance is classified as Class 3 and t
k
following minimum distances are allowed:
o
a side or rear wall.
o 700
it.
19
f
the underside of the horizontal surface is lower than 400 mm, then
50 mm clearance around the appliance and between the hob
ble materials.
hen unpacking the appliance please check that the following items
n the packaging:
nual
warranty card
elf-adhesive label for amending the gas category on the appliance’s
LPG conversion jets are used).
Cut a hole in the worktop that corresponds with the relevant
hob on the following pages.
o 400 mm between the hob surface, providing that the underside of
the horizontal surface is in line with the outer edge of the hob. I
it must be at least 50 mm away from the outer edges of the hob.
o
surface and any combusti
Unpacking the appliance
W
are contained withi
1 x Baumatic hob
Pan stands
Burner assemblies
Instruction ma
Baumatic
Fixing screws
Clamps
Sealing strip
LPG conversion jets
S
rating plate (required if the
Installing the appliance
o
drawing for your
BGG30 / BGG32
20
BGG64 BGG60 /
BGG70
All models
o IMPORTANT: You must have a gap of at least 25 mm between
the underneath of the appliance and any surface that is below it.
o Carefully turn the hob upside down and place it on a cushioned
mat.
o Apply the sealing strip (A) provided around the edge of the
appliance.
o The protective covering must be removed from both sides.
o Do not leave a gap in the sealing agent or overlap the thickness.
o IMPORTANT: Do not use a silicon sealant to seal the appliance
against the aperture. This will make it dicult to remove the hob
from the aperture in future if it needs to be serviced.
(A) Sealing strip
(B) Clamp
(C) Screw
21
23
Ventilation requirements
o The room containing the hob should have an air supply in
accordance with the current edition of BS 5440: Part 2:
o The room must have opening windows or equivalent; some
rooms may also require a permanent vent.
o If the room has a volume between 5 and 10m³, it will require an
air vent of 50cm² (effective area). Unless it has a door which
opens directly to the outside.
o If the room has a volume of less than 5m³, it will require an air
vent of 100cm² (effective area).
o If it is installed in a room with a volume that exceeds 11m³, then
no air vent is required.
o If there are any other fuel burning appliances in the same room
the current edition of BS 5440: Part 2: should be consulted to
determine air vent requirements.
o Ensure that the room containing the hob is well ventilated, keep
natural ventilation holes or install a mechanical ventilation device
(mechanical cooker hood).
o Prolonged intensive use of the appliance may call for additional
ventilation, either by the opening of a window, or by increasing
the level of the mechanical ventilation device (where present).
o This hob is not fitted with a device for discharging the products
of combustion. Ensure that the ventilation rules and regulations
are followed.
o The walls behind and near the hob should be resistant to heat,
steam and condensation.
o Remember that the quantity of air necessary for combustion
must never be less than 2m³/h for each kW of power (see total
power in kW on the appliance rating plate).
Minimum flow adjustment for hob gas taps.
All work must be carried out by a GASSAFE
registered engineer.
IMPORTANT: Always isolate the hob from the electricity supply
before changing the injectors and/or adjusting the minimum
flow of the burners.
o Switch the burner on
and set the knob at the
minimum position.
o Remove the knob from
the tap and place a
small bladed
screwdriver in the
centre of the tap shaft.
o Unscrew the adjusting screw, in order to increase the gas flow or
tighten the adjusting screw to decrease the gas flow.
o The correct adjustment is obtained when the flame has a
length of about 3 – 4 mm.
o For butane/propane gas, the adjusting screw must be tightly
screwed in.
o Refit the control knob.
o Make sure that the flame does not go out by quickly turning
from maximum flow to minimum flow. If it does then remove
the control knob and make further adjustments to the gas
flow, testing it again once the adjustment has been made.
o Repeat this process for each one of the gas taps.
26

Produktspezifikationen

Marke: Baumatic
Kategorie: Ofen
Modell: BGG60

Brauchst du Hilfe?

Wenn Sie Hilfe mit Baumatic BGG60 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Ofen Baumatic

Baumatic

Baumatic Tennesse Bedienungsanleitung

13 Oktober 2024
Baumatic

Baumatic B151BL-B Bedienungsanleitung

9 Oktober 2024
Baumatic

Baumatic BCE625SS Bedienungsanleitung

4 Oktober 2024
Baumatic

Baumatic B550 Bedienungsanleitung

3 Oktober 2024
Baumatic

Baumatic B65 Bedienungsanleitung

3 Oktober 2024
Baumatic

Baumatic B180 Bedienungsanleitung

2 Oktober 2024
Baumatic

Baumatic P76SS Bedienungsanleitung

30 September 2024
Baumatic

Baumatic RT64 Bedienungsanleitung

23 September 2024
Baumatic

Baumatic CP9BLB Bedienungsanleitung

23 September 2024
Baumatic

Baumatic BHC900 Bedienungsanleitung

23 September 2024

Bedienungsanleitung Ofen

Neueste Bedienungsanleitung für -Kategorien-

Harvia

Harvia Pro 20 WKPR20M Bedienungsanleitung

2 Dezember 2024
Harvia

Harvia Legend 150 Bedienungsanleitung

2 Dezember 2024
Harvia

Harvia Legend 300 Duo Bedienungsanleitung

2 Dezember 2024
Indesit

Indesit VL 22 S Bedienungsanleitung

16 Oktober 2024
Gaggenau

Gaggenau BMP225130 Bedienungsanleitung

16 Oktober 2024
Wolf

Wolf M Series Bedienungsanleitung

16 Oktober 2024
Princess

Princess 112741 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia HR750VGTCH Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia HR750VGTAN Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia HR640VGTCO Bedienungsanleitung

16 Oktober 2024