Atlas Sound FM250-70 Bedienungsanleitung

Atlas Sound Empfänger FM250-70

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atlas Sound FM250-70 (3 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/3
– 9 – AtlasSound.com
Specifications are subject to change without notice.
Owner’s Manual F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
FM250-4 and FM250-70 Module Features
1. Module Status Indicators
Note: They also parallel Status LED on the front panel of the F6-MF panel.
Ready This LED will illuminate Green when an FM250 power module is installed on the appropriate channel and the F6-MF is
turned on.
Signal The channel Signal LED will illuminate Green when the FM250 amplifier output signal produces a minimum 1 Watt
output.
Limit The Limit LED will illuminate Yellow under load conditions. If the FM250 function switch is set to Limit then the LED
acts as a maximum level indicator. If the FM250 channel Limit function is off, the LED reacts as a Clip indicator. Also,
under Low Impedance loads, this LED serves as a current Limit indictor.
Protect The Protect LED will illuminate Red during one the following conditions. No output will occur while this LED is
illuminated. It will reset itself after the condition has been corrected.
1) Shorted speaker output.
2) Thermal Shut Off. The Temp F6-MF TEMP LED will also be illuminated.
3) Current Overdrive. If the amplifier channel is driving too low of a speaker load.
2. Speaker Connections
A removable Phoenix/Euro Block type connector is supplied to connect your speakers to the FM250 amplifier module. It is
recommended to use 16-gauge wire or lower for connection to the speakers. Do not overload the amp by connecting too many Note:
speakers to the amp.
Protect
Limit
Signal
Ready
Speaker Output
Class 2 Wiring
4Ω
FM250 - 4
250W @ 4Ω
Protect
Limit
Signal
Ready
Speaker Output
Class 2 Wiring
70V
FM250 -70
250W @ 70V
AtlasSound.com – 10 –
Specifications are subject to change without notice.
Owner’s Manual
F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
FM250-4 & FM250-70 Function Switch
FM250 Module Dip Switch Functions are located near the rear of the FM250 modules. It is essential to preset your setting prior Note:
to inserting the module into the F6-MF.
Factory Dip Switch Presets
Dip Switch 1 ships in the “On” position. Dip Switches 2 & 3 ship in the “Off” position.
Dip Switch 1, Gain
When placed in the “On” position the channel’s Gain or Input Sensitivity will be 1V (0dBV) for rated output. When placed in the “Off”
position the Gain is set to 2V (6dBV).
Dip Switches 2 & 3, HPF
The High Pass Filter (HPF) when placed into the “On” position engages a 100Hz / 12dB filter. When in the “Off” position the module
operates at full audio bandwidth.
– 11 – AtlasSound.com
Specifications are subject to change without notice.
Owner’s Manual
F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
FM250 Amplifier Module Installation
Use the following steps and read all steps prior to installation.
1. Turn F6-MF AC Power Switch to the “Off” position.
2. Turn down all level controls on the front panel.
3. Remove the blank card slot cover. Do not discard the two screws, you will need them later.
4. Set the function switches on the FM250 module. (See Page 10)
5. Carefully and slowly guide the module into the slot with the PCB components facing to the right. The module heatsink Note:
top and bottom metal edge mate with the mainframe plastic card guides. Do not force the card. Realign if necessary.
6. After the module is pushed in and in contact with the back plane of the PCB assembly mating connector, firmly press the
module in completing the connection. If the module plate is flush to the F6-MF, the module is fully seated.
7. Insert the two screws from the cover pate. Some minor alignment may be required.
Align Modules to
Top & Bottom Card
Guides

Produktspezifikationen

Marke: Atlas Sound
Kategorie: Empfänger
Modell: FM250-70

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atlas Sound FM250-70 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Atlas Sound

Atlas Sound

Atlas Sound DPA-DAC4 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound HPA-DAC2 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound CLA402 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound CLA404 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound CLA202 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound CLA804 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound HPA2408 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound HPA-DAC4 Bedienungsanleitung

5 September 2024
Atlas Sound

Atlas Sound HPA2604 Bedienungsanleitung

3 September 2024
Atlas Sound

Atlas Sound F6-MF Bedienungsanleitung

22 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024