AstralPool RPX Robotic Pool Cleaner Bedienungsanleitung

AstralPool Diversen RPX Robotic Pool Cleaner

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr AstralPool RPX Robotic Pool Cleaner (19 Seiten) in der Kategorie Diversen. Dieser Bedienungsanleitung war fĂĽr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/19
Installation and Operating Instructions
RPX Robotic Pool Cleaner
Product 11714
Product Inst 323
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL THE INSTRUCTIONS
CAUTION: Do not plug the power supply into a grounded outlet or do not switch the
pool cleaner “ON” if it is not fully immersed in water. Operating the cleaner out of water
will cause severe damage immediately and will result in loss of warranty.
Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its
cleaning cycle. This will allow the motors to cool adequately. Do not leave the cleaner
in the pool all the time. Always remember to turn the power supply “OFF” and unplug it
from the power outlet before removing the cleaner from the pool.
WARNING: The cleaner must not be used when people are in the water. For use
with swimming pool only
Safety Note
- The unit must be supplied through a residual current device (RCD) having a rated
residual operating current not exceeding 30 mA
- The connection to the branch circuit should be consistent with the local and national
wiring rules (electrical code).
- Mishandling of the unit can result in leakage of lubricants.
- If the supply cord is damaged, it must be replaced by the manufacturer’s service
agent or a qualified and trained person in order to avoid hazards.
Dear Customer,
Thank you for choosing our product to clean your pool. We hope that you will enjoy
using your new robot to maintain your swimming pool for years to come.
Before you begin to use your robot, please take a few minutes to carefully read these
operating instructions.
Again, thank you for choosing our product.
2
Components
Your new automatic pool cleaner contains:
- The robotic pool cleaner with its floating cable.
- The Power Supply (transformer).
- Caddy
Please read this manual completely before operating your pool cleaner.
While the appearance of your cleaner and some of its components may differ from those
shown here, the function of the cleaner, operating procedures and maintenance
practices are the same.
WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current
Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent
any possible electric shock.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
Side Plate
Handle
Handle Lock
Mechanism
Drive Track
Scrubbing Brush
Unit Body
Outlet Top
SAVE THESE INSTRUCTIONS
12 cm
(4 inch)
3.6m/11.8ft
1
1a
1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and at
least 12 cm / 4 Inch above the surface (fig.1). The transformer will supply low voltage to
the cleaner.
2. Uncoil the cable.(fig.1a)
3. For proper operation, lock the moveable handle diagonally across the top of the
cleaner's body. Push down on the handle lock mechanism and slide the handle all the
way to the end (recommended one slot before the end), then release the lock.
Depending on your model, the handle lock button might be vertical or horizontal
(fig.2a, 2b). The handle will remain fixed in this position. Repeat this process on the
other side of the cleaner.
Remember, the handle must be fixed diagonally (fig.2c)
2b
unit
2c2aHandle lock vertical Handle lock horizontal
Operating the pool cleaner
4. Place the unit in the water. Turn the unit
side to side in the water to allow air to
escape from the body and then let the
cleaner sink to the bottom of the pool
(fig.3). Then, spread the cable over the
surface of the pool as evenly as possible
(fig.1).
3
3
5. Plug the cable into the power supply. Make sure the key on the plug corresponds
exactly with the key slot on the socket of the power supply (fig. 3a).
Plug the power supply into a grounded outlet. Ensure that the electric outlet has been
properly grounded (fig.3b). Press the “ON” button on the power supply. The light will
glow indicating that the system is “ ON “ and the pool cleaner will start the cleaning
cycle. The unit keeps record of the number of cleaning cycles. Only an authorized
service center can display the accumulated cleaning cycles. (See details on the next
page)
3b
3a

Produktspezifikationen

Marke: AstralPool
Kategorie: Diversen
Modell: RPX Robotic Pool Cleaner

Brauchst du Hilfe?

Wenn Sie Hilfe mit AstralPool RPX Robotic Pool Cleaner benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Diversen AstralPool

AstralPool

AstralPool RTX Robotic Pool Cleaner Bedienungsanleitung

26 August 2024
AstralPool

AstralPool Dolphin Easykleen Bedienungsanleitung

26 August 2024
AstralPool

AstralPool RPX Robotic Pool Cleaner Bedienungsanleitung

26 August 2024

Bedienungsanleitung Diversen

Neueste Bedienungsanleitung fĂĽr -Kategorien-

ION

ION ICADE Bedienungsanleitung

16 Oktober 2024
Walkera

Walkera Goggle 3 Bedienungsanleitung

16 Oktober 2024
Walkera

Walkera Goggle 4 Bedienungsanleitung

16 Oktober 2024
Kerbl

Kerbl 81685 Cat flap Bedienungsanleitung

6 Oktober 2024
Tanita

Tanita HC-212F Breath Checker Bedienungsanleitung

6 Oktober 2024
Somfy

Somfy Telis Lounge Bedienungsanleitung

5 Oktober 2024
Navman

Navman NavBus Bedienungsanleitung

5 Oktober 2024
Trelock

Trelock LS 320 Bedienungsanleitung

5 Oktober 2024
Bobike

Bobike Maxi City Bedienungsanleitung

5 Oktober 2024
Tanita

Tanita 1210N Bedienungsanleitung

5 Oktober 2024