Arcam FMJ P25 Bedienungsanleitung
Arcam
Verstärker
FMJ P25
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Arcam FMJ P25 (14 Seiten) in der Kategorie Verstärker. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/14
Integrated Amplifier
Power Amplifier
DAVE Amplifier
MARC Amplifier
PEMBROKE AVENUE, DENNY INDUSTRIAL CENTRE, WATERBEACH, CAMBRIDGE CB5 9PB, ENGLAND
TELEPHONE: 44+(0) 1223 203203 FAX: 44+ (0) 1223 863384 e-mail: support@arcam.co.uk www.arcam.co.uk
SH080EISSUE 1
EnglishFrançaisDeutsch
3
This Handbook covers 4 different models, as follows:
An integrated amplifier
A power amplifier
The DAVE (Digital Audio Video Entertainment) amplifier
The MARC (Multi Area Remote Control) amplifier
SAFETY
There are 19 safety items, set out on page 25 of this Handbook.
For your own safety, and to ensure that your amplifier works
properly, we strongly recommend that you read them.
SOUND CUTS OUT FOR NO APPARENT REASON
If the temperature of the internal heatsinks rises above a safe level,
then a thermal cut out inside the amplifier will operate.
The POWER INDICATOR on the front panel will turn orange and
the protection system will temporarily remove the power to the
speakers. The system will reset itself as the heatsinks cool down.
When playing a heavily recorded CD it is possible to drive the A22
at full power despite the fact that the volume is not at maximum.
This is because of the high output voltage from a CD player.
AMPLIFIER DOESN’T SWITCH BACK ON
All amplifiers have a 'protection mechanism' which will be
activated if you switch the unit on again immediately after turning it
off.The mechanism may stop it being turned back on.
If the mechanism activates, wait 30 seconds, then try again.
For ease of use, this handbook has been divided into 4 sections.
Integrated amplifier
Power amplifier
DAVE (Digital Audio Video Entertainment) amplifier
MARC (Multi Area Remote Control) amplifier
Each of the sections has a short introduction to the product,
followed by an 'User Guide' which is primarily for users who have
had their system installed by their dealer or supplier.
Following the 'User Guide' is a section describing 'Advanced
Features' (depending on the complexity of the product).
Finally for customers wishing to set up their own system, a section
called 'Setting Up'.
Integrated amplifier
User Guide 4
Using the Remote Control Handset 5
Advanced features 6
Setting up 7-8
Bi-wiring your speakers 9
Bi-amping 10
Power amplifier
User Guide 11
Setting up 12
Integrated and Power amplifiers - Technical Specifications 13
DAVE amplifier
(HOME THEATRE MODULE)
User Guide 14
Setting up 15-19
Advanced features 20
Remote Control Handset 21
MARC amplifier
(MULTI AREA MODULE)
User Guide 22-23
Advanced Features 24
Safety Guidelines 25
Guarantee 26
Thank you for choosing ARCAM
CONTENTSFOUR MODELS
IMPORTANT NOTES
A microprocessor is at the heart of the amplifier.
It performs several important functions. It switches the amplifier on
or off from standby mode and mutes the two sets of speakers
individually as well as the pre-amp output. It is also responsible for
the remote bus and infra red remote input. Parameters can be
selected, and displayed, on the built in graphic display enabling easy
set up of the amplifier and simple source selection. In addition, the
amplifier uses LED markers to indicate the primary source which is
in use. In addition to a full suite of audio line level inputs, there is
also a high quality optional MM/MC phono stage.To protect your
amplifier, the microprocessor monitors the heatsink temperature
and RF content of the speaker outputs. In the event of the amplifier
being over driven, it can activate the automatic speaker protection
circuits and it can report fault conditions to the main display.
dn POWER
Switches the unit on and off.The unit can also be switched
into ‘standby’ by use of the remote control handset.
do POWER INDICATOR
This will initially glow amber. After a few seconds, it will glow
green. When the indicator glows amber, the speakers are
disconnected and an internal protection circuit is activated.
The power indicator will turn red if the unit has been put
into standby mode by use of the remote control.
Under certain conditions the power indicator may flash and
a fault condition will be shown on the displaydp. If this
happens you should unplug the mains lead of the unit and
leave the unit for a few minutes before re-connecting.
If the fault condition persists unplug and contact your Arcam
dealer.
dk SP1
Selects or de-selects the main (upper) pair of speakers.
Push the button in to select.
dl SP2
Selects or de-selects the secondary (lower) pair of speakers.
Push the button in to select.
Important note: If both switches are turned off the amplifier
will appear not to work, as all speakers will be switched off!
cr VOLUME
Adjusts the volume level of the loudspeakers, pre-amp out
and headphones.The volume can also be controlled with
the Remote Control Handset. As the volume knob is not
motorized the knob will not move when adjusted remotely.
If you spin the knob quickly it will not change the volume.
This is to prevent accidentally setting the volume too high.
NOTE ON VOLUME CONTROL SETTINGS
It is important to realise that the position of the volume
control is not an accurate indication of the power delivered
to your loudspeakers. The amplifier will often deliver its full
power long before the volume control reaches its maximum
position particularly when listening to heavily recorded
compact discs.
However the amplifier also has to be capable of giving full
power output from much lower level sources, such as tuners
and cassette decks. Using these sources, the volume control
setting may be much higher before distortion (audible
overload) sets in.
BALANCE
Press CONTROL cq, turn the volume knob to the
desired balance, then press CONTROL again to fix the
balance you have selected.
cq CONTROL
This button cycles (or steps) through the functions that can
be controlled by the volume knob.This can be either
volume (the default setting) or balance. If you have a
DAVE or MARC, there are several other functions.
Refer to those sections of this handbook.
cs ENTERTAINMENT (SOURCE) SELECTORS
These buttons select the source (i.e. Radio (TUNER),
Compact Disc (CD) etc. you wish to listen to.
dq REMOTE RECEIVER
The remote receiver is behind the FMJ badge.
Make sure the remote receiver is not covered or signals
from the Remote Control Handset will not be received.
dm HEADPHONES SOCKET
Accepts headphones rated between 8 ohms and 2k ohms
fitted with a 1/4” stereo jack plug. If you wish to listen on
headphones only, use SPl and SP2 (if necessary) to mute the
speakers.The headphone socket is always active.
Integrated amplifier - User Guide
4
Circled numbers in the text, e.g. 7, refer to the numbers on the
pictures. If your integrated amplifier HAS NOT been installed for
you, you should read the section entitled ‘Setting up’ before using the
‘User Guide’.
cn co cp cq dkct dl dm dncscr
dodp
dq
PHONO/AUXMODE CONFIRM RECORD CONTROL CD TUNER AV DVD VCR PROCESSOR
2 TAPE 1
SP1 SP2 PHONES
A22 INTEGRATED AMPLIFIER
POWER
V
V
V
V
Vol
ol
ol
ol
olum
um
um
um
ume
e
e
ee CD
CD
CD
CD
CD
INTRODUCTION
IN USE
5
Integrated amp - Using the Remote Control
Don’t forget to fit the two AAA batteries
supplied and ensure they are inserted
correctly into the back of the remote
control before using it.
The Remote Control sends a message to an
infrared receiver which is located behind the
FMJ badge on the front of the amplifier.
Do not place anything in front of the badge
or the Remote Control may not work.
VOLUME AND (MUTE)
Press ‘+’ to increase volume or ‘–’ to
decrease the output volume of the amplifier.
Press ‘ ‘ to mute the speaker connections
and preamp outputs. Both tape outputs and
the headphone socket remain active. Mute is
disabled either by pressing ‘ ‘ again, or by
adjusting the volume.
CD CONTROLS
These offer basic controls of Arcam CD
players, such as the FMJ CD23.
DAVE REMOTE CONTROL
If you have a DAVE amplifier, you will have the the CR9000
Remote Control as shown in the DAVE amplifier section
of this handbook.That Remote Control allows you to
operate the integrated amplifier plus some basic functions
of an Arcam or Philips based CD player or Tuner.
TUNER
These buttons are used to control tuner
functions.
Note that the FM/DAB lights indicate into
which mode you are switching the remote
control.The lights only illuminate for five
seconds to conserve battery power.
If neither light is illuminated this does not
mean that the remote control is not
working!
SOURCE SELECTION BUTTONS
These operate in the same way as the
source selectors on the front panel of your
integrated amplifier.
DISP
Cycles through the settings ‘Bright’, ‘Off ’ and
‘Dim’.Turning the display ‘Off ’ generally
gives a slight improvement in sound quality.
SP1 AND SP2
These buttons allow you to select and
deselect the main(SP1) and secondary
(SP2) sets of speakers attached to your
amplifier (see page 4).
POWER/STANDBY
Toggles the amplifi er between standby
mode and full power mode.The power
indicator light next to the power button
on the front panel is red if the amplifier
is in standby, amber while the amplifier is
powering up (this only takes a few seconds)
and green when the amplifier is powered up.
If you have an integrated amplifier or MARC amplifier, you will have a Remote Control
similar to the one shown below.
This CR-389 Remote Control gives access to all functions available on the front panel
of FMJ amplifiers. It also has controls to operate Arcam CD players, AM/FM tuners
andDAB tuners.
The Remote Control transmits Philips RC-5 type codes.
OTHER AMPLIFIER FUNCTIONS
Note that greyed-out buttons on the
remote control diagram are of use with
other Arcam amplifiers.
Produktspezifikationen
| Marke: | Arcam |
| Kategorie: | Verstärker |
| Modell: | FMJ P25 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Arcam FMJ P25 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Verstärker Arcam
7 Juli 2024
7 Juli 2024
6 Juli 2024
6 Juli 2024
6 Juli 2024
5 Juli 2024
5 Juli 2024
5 Juli 2024
5 Juli 2024
4 Juli 2024
Bedienungsanleitung Verstärker
- Verstärker Nedis
- Verstärker Sony
- Verstärker Yamaha
- Verstärker Alecto
- Verstärker MarQuant
- Verstärker Kenwood
- Verstärker Pyle
- Verstärker Auna
- Verstärker Beyerdynamic
- Verstärker Denon
- Verstärker Pioneer
- Verstärker Geemarc
- Verstärker JBL
- Verstärker Onkyo
- Verstärker Technics
- Verstärker Hifonics
- Verstärker Novero
- Verstärker Fenton
- Verstärker Rotel
- Verstärker Harman Kardon
- Verstärker Marshall
- Verstärker Naim
- Verstärker Power Dynamics
- Verstärker Samson
- Verstärker Skytec
- Verstärker Tangent
- Verstärker Vonyx
- Verstärker NAD
- Verstärker Fender
- Verstärker Behringer
- Verstärker Marantz
- Verstärker Crown
- Verstärker Ecler
- Verstärker Luxman
- Verstärker Monacor
- Verstärker Sansui
- Verstärker TEAC
- Verstärker Thorens
- Verstärker Classé
- Verstärker Sherwood
- Verstärker Humantechnik
- Verstärker Bluetech
- Verstärker Skytronic
- Verstärker Reloop
- Verstärker Eden
- Verstärker American Audio
- Verstärker Anthem
- Verstärker HQ Power
- Verstärker Ibiza Sound
- Verstärker McIntosh
- Verstärker Hartke
- Verstärker DAP Audio
- Verstärker Elektra
- Verstärker Engl
- Verstärker Iriver
- Verstärker Koda
- Verstärker Konig Electronic
- Verstärker MaxGear
- Verstärker Meridian
- Verstärker Peavy
- Verstärker Quadral
- Verstärker Randall
- Verstärker Stagg
- Verstärker UPC
- Verstärker Velodyne
- Verstärker IFi Audio
- Verstärker Amplicom
- Verstärker Ampeg
- Verstärker Citronic
- Verstärker Advance Acoustic
- Verstärker Mark Levinson
- Verstärker AB International
- Verstärker Alto Professional
- Verstärker Audica
- Verstärker Bellman
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
15 Oktober 2024
12 Oktober 2024
9 Oktober 2024
22 September 2024
19 September 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024