APart SDQ5P-W Bedienungsanleitung

APart Lautsprecher SDQ5P-W

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für APart SDQ5P-W (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

The APart SDQ5P powered loudspeaker set is a very compact, easy to use, plug and play

sound system. It consists of one amplied loudspeaker with a 5.25” woofer, a quality high

frequency unit and a second linkable passive loudspeaker.

The speakers are magnetically shielded, altough some small radiation is inevitable.

1. Volume control : With this button you can easily set the desired volume.

2. Treble control : Herewith you can add or decrease the high frequency. Adding high frequency can

improve the intelligibility. Adjust it to the desired level. In the centre position the

sound should be neutral.

3. Bass control : By adding bass you can add warmth to your music. Decreasing bass can improve the

intelligibility of spoken messages, certainly in reverberant rooms.

4. On/Oﬀ : When the AC plug is connected to the mains circuit, you can turn the unit on or oﬀ with this

button. When the unit is switched ON, the green led should illuminate.

5. Clip leds : Each channel has its clip led, indicating that max. power is reached.

The system should be used without activating this red warning leds.

Turn down the volume if these leds are ashing.

When you neglect this warning, your system may get overheated or damaged.

6. RCA inputs : Here you can connect your sound source. These inputs have to be fed with a input

signal at LINE level (cd, dvd, vhs, tuner, mixing table…..). Connecting a microphone will give bad

result. In this case, you should use a microphone mixer or preamplier.

The left RCA plug (red) will feed the built in amplier for the passive external loudspeaker. The right

(white) plug will send your music to the amplied main unit.

7. 3, 5 mm stereo jack input : This line level stereo input is very useful to connect you

computer, portable sources (CD, MD, MP3 players, …).

8. Balanced line inputs : These three pin inputs can be used to feed the line level signals from devices

with balanced outputs (Shield, hot, cold). Balanced wiring is recommended when the input lines are

long or placed in a interpherence area. When hum appears when feeding the line input, it can be

useful not to connect the shield at the SDQ5P side. These signals will be mixed with the signals fed

into the rca and jack input, meaning you can use them at the same time.

9. Speaker output : These two pin euroblock plug should be used to feed the shipped passive loud-

speaker. Using other loudspeakers can give bad result and even cause damage to the main SDQ unit.

Be sure the “+” socket of the main unit is connected to the “+” of the passive

loudspeaker and the “-“ to “-“.

10. Mode switch : This switch turns your SDQ5P in a full stereo or a very compact full option mono

system. When switched to the mono mode, you should only use the “Left” inputs. From this input left

and right amplier will be fed.

11. Mains socket : The unit can be branched to the mains circuit by a standard IEC type power cord.

This socket contains a 1 A slow blow fuse. Use a screw driver to ip out the fuse compartment and

to replace the fuse. When this fuse blows frequently you should bring the SDQ to a qualied service

centre. First check whether you didn’t use a quick-blow fuse.

To avoid ground loops, certainly when using audio signals from computers, this socket doesn’t contain

a ground pin!

12. Heat sink : When using your SDQ5P at full power and for a long time, this heat sink might become

very hot, do not touch ! Take care when placing it to close to other items sensitive to heat.

Produktspezifikationen

Marke:	APart
Kategorie:	Lautsprecher
Modell:	SDQ5P-W
Gewicht:	5750 g
Produktfarbe:	Weiß
Impedanz:	8 Ohm
Material:	Kunststoff
RMS-Leistung:	60 W
Typ:	Unterputz/auf Putz/Decke Lautsprecher
Audio Kanäle:	2.1 Kanäle
THD, totalklirren:	0.07 %
Rauschverhältnis (SNR):	90 dB
Frequenzbereich:	45 - 20000 Hz
Hochtöner:	Ja
Abmessungen (BxTxH):	181 x 170 x 238 mm
Hochtönerdurchmesser:	25.4 mm
Tieftönerdurchmesser:	133.4 mm