APart MASK8-BL Bedienungsanleitung

APart Lautsprecher MASK8-BL

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für APart MASK8-BL (7 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/7

The senior MASK is a full range loudspeaker ﬁ tted with an 8” LF driver and our smooth

sounding ferro-ﬂ uid cooled silk dome tweeter on a 360° Waveguide horn for high output,

without getting aggressive.

The coated paper cone together with the stiff suspension results in a well controlled sound.

This wooden bass reﬂ ex loaded model is only in 8Ω available.

You can use the MASK 8 anywhere you need a BIG sound from a rather small enclosure.

To improve reproduction of lower frequencies, it is advisable to add (powered) sub-

woofers to your sound system.

To calculate the number of subwoofers needed, determine the maximum rated output

of a single subwoofer. Placing your subwoofer near one or more boundaries, increases

the SPL by 3-6dB for each boundary (for certain frequencies).

SUB2400

SUB2200 SUB-A165

1. Keep this manual for future reference.

2. Clean only with dry cloth.

3. Do not operate near heaters or place it on other apparatus which produce a lot of heat.

4. Take care for the speaker leads. Never use damaged leads and install them in such

a way that no one can walk on it.

5. Only use accessories speciﬁ ed by the manufacturer.

6. Make sure the mounting surface can easily support the speaker’s weight.

7. Use only industry-accepted rigging tools and methods.

8. Choose the right speaker for the right job.

9. Use sufﬁ cient loudspeakers and avoid death spots.

10. No main power shall be connected to the loudspeakers.

11. This apparatus should only be serviced by qualiﬁ ed personnel. If not, the warranty might be void.

12. Removal of the grill causes risk to loudspeaker damage.

13. Use cables of the right gauge, certainly for long runs.

14. Use cables with clear colour codes and maintain polarity throughout the whole system.

15. Switch ampliﬁ ers on with the volumes turned down completely to avoid loud clicks and clacks.

16. Avoid loud feedback for this is a main speaker killer!

17. Please check the unit’s condition after unpacking. If the outside of the carton box has been damaged, inform

your shipper immediately.

Music colours our life but too much sound might damage yours and others hearing permanently!

Being exposed to loud sound levels over a long time can cause severe hearing loss. Don’t forget to

consult the local law regulations regarding producing sound in public places. In some countries ear

protection is obliged when the continuous sound level over 8 hours time is 80dB (A). Each halving of

time allows an increase of 3dB.

Too week ampliﬁ ers can burn your speakers

By pushing your ampliﬁ er or its inputs too much, your amp can produce more power than the power

published in his manual.

This power is not always clean and can be very distorted. When such signal is fed into your loud-

speakers for a longer period, damage can be the result. Don’t cut in the budget of your ampliﬁ er. A

loudspeaker can demand to ten times the average power to reproduce those smashing sonic bursts

you are kicking on. If your ampliﬁ er has enough reserve power, your sound will remain clear. When

you squeeze your amp’s throat, he’ll be pushed to produce sounds which will kill your tweeters ﬁ rst.

Protection systems are not built to be activated all the time, they are there to warn you and to

give you a safe margin!

Two parallel wired speakon 4 connectors are available (wired +1/-1).

To avoid confusion, use cables which have clear (colour) codes, so correct polarity can be

maintained. Also use wires of the right gauge, certainly for longer distances.

Load 2,5mm² 4mm²

2 Ω <7.5m <12,5m

4 Ω <15m <25m

8 Ω <30m <50m

16 Ω <60m <100m

equity between loss and cable length

As long as you stay under these cable

lengths the loss of ampliﬁ er power

will remain below +/- 10%.

Produktspezifikationen

Marke:	APart
Kategorie:	Lautsprecher
Modell:	MASK8-BL
Gewicht:	8100 g
Produktfarbe:	Schwarz
Impedanz:	8 Ohm
Material:	Holz
RMS-Leistung:	200 W
Typ:	Unterputz/auf Putz/Decke Lautsprecher
Audio Kanäle:	2.0 Kanäle
Frequenzbereich:	60 - 30000 Hz
Hochtöner:	Ja
Abmessungen (BxTxH):	250 x 250 x 411 mm
Hochtönerdurchmesser:	25.4 mm
Musik Energie:	300, 600 W
Tieftönerdurchmesser:	203.2 mm