AMX NXD-500iW-MW Bedienungsanleitung

AMX Monitor NXD-500iW-MW

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AMX NXD-500iW-MW (2 Seiten) in der Kategorie Monitor. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Installation Guide

NXD-500IW 5" Water-Resistant Wall/Flush Mount Touch Panel

For more detailed installation, configuration, programming, file transfer, and operating

instructions, refer to the NXD-500i Operation/Reference Guide, available online at

www.amx.com.

Overview

The NXD-500IW widescreen color panel is designed for use in high-humidity INDOOR

environments ranging between 50 and 95% relative humidity. It includes a built-in

microphone, speakers, a mini-USB port for programming and audio output, and one

NetLinx-programmable button. All power is supplied via Power Over Ethernet (PoE),

utilizing a PS-POE-AF PoE Injector (FG423-80) or equivalent PoE device. The 

NXD-500IW comes in Mystique black (NXD-500IW-MB, FG2261-09) and Mystique

white (NXD-500IW-MW, FG2261-12).

The NXD-500IW supports Intercom functionality, which allows two communicating

panels (controlled by the NetLinx Master) to transmit full-duplex audio signals over a

network in order to be used as an Intercom system.

Specifications

IP Rating Compliance (Indoor Use Only)

The NXD-500IW is IP Rating 51 compliant. Ingress of dust is not entirely prevented,

but it will not enter in sufficient quantity to interfere with the satisfactory operation of

the device; complete protection against contact. Dripping water (vertically falling

drops) shall have no harmful effect.

Panel Connectors and Wiring

FIG. 2 shows the connectors located on the NXD-500IW Modero panel. The mini-USB

port is used both for programming the touch panel and for audio output. The mini-USB

port automatically detects the presence of a headphone adaptor, allowing the port to

be used for headphone connectivity.

For more information on connection and use of the Panel Connectors, as well as

information on programming and headphone connectivity, please refer to the

NXD-500i Operation/Reference Guide, available at www.amx.com.

Front Bezel Button

The NXD-500IW has only one button on the front of the device, in the center of the

bezel. This button has several uses:

• Press the button once to start a previously programmed function, or to turn off

the display if not previously programmed.

• Press and hold the button for 6 seconds to put the device into Setup Mode.

• Press and hold the button for 9 seconds to enter Calibration Mode.

• Press and hold the button for 20 seconds to reboot the panel.

FIG. 1 NXD-500IW-MW 5" Modero Widescreen WallMount Touch Panel

NXD-500IW (FG2261-09/12) Specifications

Dimensions (HWD): • NXD-500IW (with bezel): 4.15" x 5.59" x 1.97" 

(10.50 cm x 14.20 cm x 5 cm)

• CB-TP5 Rough-In/Wallbox (optional): 4.27" x 5.14" x 3.40" 

(10.86 cm x 13.06 cm x 8.64 cm)

Power 

Requirements:

• PoE Powered - No local Power Supply needed

• Max power draw: 5.5W.

Memory (Factory

default):

• 128 MB SDRAM

• 256 MB integrated Flash Memory (not upgradeable - factory

programmed)

Weight: • 0.80 lbs (0.36 kg)

Certifications: • FCC Part 15 Class B

• CE

• IEC 60950

• RoHS

Panel LCD 

Parameters:

• Aspect ratio: 16 x 9

• Maximum brightness (luminance): 200 cd/m2

• Channel transparency: 8-bit Alpha blending

• Contrast ratio: 250:1

• Display colors: 256 thousand colors (18-bit color depth)

• Dot/pixel pitch: 0.14 mm

• Panel type: TFT Color Active-Matrix

• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame

frequency

• Viewing dimensions: 4.3" x 2.58" (109.2 mm x 65.2 mm)

Active Screen Area: • 4.25” x 2.55” (10.80cm x 6.48cm)

Viewing Angles: • Up/Down/Left/Right: 85/85/85/85

IR Reception Angle: • Horizontal: + 25° (left and right from center)

• Vertical: + 15° (up and down from center)

Supported Audio

Sample Rates:

• 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz,

12000Hz, 11025Hz, and 8000Hz.

Intercom: • Full duplex VoIP capabilities.

Front Panel Components:

Light Sensor: • Photosensitive light detector for automatic adjustment of the

panel brightness.

Motion Sensor

(PIR):

• Proximity Infrared Detector to wake the panel when panel is

approached.

Front Bezel Button: • Provides both access to the Setup and Calibration pages and

toggles the panel between a “sleep” or “wake” state. This button

is also user-programmable.

Front Bezel Button Bezel

Speaker

Touch screen

Microphone

NXD-500IW Specifications (Cont.)

Front Panel Components (Cont.)

Microphone: • Frequency response of 300 to 3400Hz; used for intercom

applications.

Speaker: • Output of 4Ohm, 2 Watts, with a 300Hz low cutoff frequency.

Side Panel Connectors:

Ethernet 10/100

Port:

• RJ-45 port for 10/100 Mbps communication. The Ethernet port

automatically negotiates the connection speed (10 Mbps or 100

Mbps), and whether to use half duplex or full duplex mode.

Power is supplied through Power Over Internet (PoE). NXD-

500IW panels communicate with the NetLinx Master using the

ICSP protocol over Ethernet. LEDs show communication activity,

connections, speeds, and mode information:

L/A-link/activity - Yellow LED lights On when the Ethernet cables

are connected and terminated correctly and then blinks when

receiving Ethernet data packets.

SPD-speed - Green LED lights On when the connection speed is

100 Mbps and turns Off when the speed is 10 Mbps.

Mini-USB

Connector:

• 5-pin Mini-USB connector used for programming, firmware

update, and touch panel file transfer between the PC and the

target panel. The connector is also used for providing audio

output for external speakers.

Operating /Storage

Environments:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Operating Humidity: 5% - 95% relative humidity

(non-condensing)

• Storage Temperature: -20° C (-4° F) to 60° C (140° F)

• Storage Humidity: 5% - 85% RH

• Indoor Installation and Operation ONLY

Included 

Accessories:

• NXD-500IW Installation Guide (93-2261-09)

Other AMX 

Equipment:

• CB-TP5i Rough-In/Wallbox (FG038-11)

• Back Cover for the CB-TP5i Rough-In/Wallbox (FG038-12)

• PS-POE-AF PoE Injector (FG423-80)

• CC-USB Type-A to Mini-B 5-wire programming cable 

( )FG10-5965

• USB to Headphone Adaptor (FG5966-23)

FIG. 2 Connector layout on the NXD-500IW

Ethernet 10/100 port

Mini-USB port

Back box

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

1/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2261-09 REV: A

NXD-500IW Setup and System Connection

1. Carefully remove the panel from the shipping box, peel the protective plastic

cover from the LCD, and apply power to the panel via the PoE Injector.

2. From below the LCD, press the Front Bezel button for 9 seconds (passing over

the Setup page) to access the Calibration setup page and follow the on-screen

instructions to return to the main Setup page.

3. Press the on-screen Protected Setup button on the Setup page.

4. Enter the panel password into the on-screen keypad (default is 1988).

5. Press the Device Number field to open the on-screen Device Number keypad

and enter a value for the panel (default is 32001).

6. Press the System Connection button to open the System Connection page.

7. Toggle the DHCP Static field to DHCP.

8. Toggle the Type field to Ethernet.

9. Toggle the Mode field to URL.

10. Enter both the System Number and IP Address of the target Master.

11. Enter a valid Username and Password if the target Master is secured.

12. Press the Back button and then press the on-screen Reboot button to save

any changes and cycle power to the panel.

Installation of the NXD-500IW

For more information on the installation of the NXD-500IW, please refer to the NXD-

500i Operation/Reference Guide, available at www.amx.com.

The NXD-500IW is contained within a clear outer housing known as the back box

(FIG. 3). This back box is removed when installing the device into a wall or into a

Rough-In Box.

Removing the Bezel

In certain circumstances, the bezel must be removed. Because the device is installed

against a wall, the bezel must be removed carefully to prevent the two top prongs

from being broken. To remove the bezel:

1. Gently lift up on the bezel from the bottom. Do NOT pull up from the sides or

the top.

2. Let the bezel fall forward from the top of the device and let it pivot from the bot-

tom.

3. Remove the bezel from the two bottom prongs.

4. When reattaching the bezel to the device, make sure to align the Microphone,

Light, and PIR Motion sensor locations on the device to their respective

openings on the bezel assembly.

NOTE: Do not remove the gasket on the underside of the bezel. If the gasket should

accidentally detach itself, gently reinsert it in the gasket channel running around the

center hole in the bezel. Do NOT stretch the gasket while reinserting it.

Installing the NXD-500IW into a wall

Unlike most AMX touchpanels, the NXD-500IW comes with a clear plastic backbox

(FIG. 7) designed to attach the panel to most standard wall materials. This backbox

has a locking tab on three of the four faces (missing only on the face containing the

space for the connections) to help lock the backbox to the wall. These locking tabs

are only extended AFTER the backbox is inserted into the wall.

WARNING: When installing the backbox, make sure that the assembly is in the

correct position and in the correct place. Once the locking tabs are extended and

locked into place, removing the backbox may be difficult without having access to the

back of the wall or causing damage to the wall.

Note: In order to guarantee a stable installation of the NXD-500IW, the thickness of

the wall material must be a minimum of .50 inches (1.27cm) and a maximum of .875

inches (2.22cm).

WARNING: The maximum recommended torque to screw in the locking tabs on the

plastic back box is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the

tab screws, such as with powered screwdrivers, can strip out the locking tabs or

damage the plastic back box.

1. Prepare the area by removing any screws or nails from the drywall before

beginning the cutout process.

2. Cut out the surface for the back box. Refer to the dimensions in the NXCD-500i

Operation/Reference Guide, available from www.amx.com, for more 

information.

CAUTION: Making sure that the actual cutout opening be slightly smaller than the

provided dimensions is highly recommended. This action provides the installer with a

margin for error if the opening needs to be expanded. Too little wall material removed

is always better than too much.

3. Remove the bezel from the NXD-500IW.

4. Gently unscrew the two screws attaching the NXD-500IW to its back box.

These are at the bottom of the device, underneath the touch screen. Carefully

remove the NXD-500IW from the back box.

NOTE: While the screws are loosened, you can adjust the LCD to ensure that it is

parallel to the sides of the backbox, if necessary. While adjusting the LCD is

possible, it is not required in most cases.

5. Thread the incoming Ethernet and mini-USB wiring (if mini-USB access is

desired) from their terminal locations through the surface opening. Leave

enough slack in the wiring to accommodate any re-positioning of the panel.

6. Push the back box into the wall opening. Insure that the locking tabs lie flush

against the back box.

7. Extend the locking tabs on the sides of the back box by tightening the screws

inside the box until snug. Not all of the tabs must be extended to lock the back

box in place, but extending a minimum of the top and bottom tabs is highly

recommended. Apply enough pressure to the screw head to keep the box flush

with the wall: this ensures that the locking tabs will tighten up against the inside

of the wall. 

The back box is clear to allow visual confirmation that the tabs have been

extended and are gripping the wall, as well as in assisting with removal if

necessary

8. Insert both connectors into their corresponding locations along the left side of

the NXD-500IW touch panel.

9. Test the incoming wiring by attaching the panel connections to their terminal

locations and applying power via the PoE Injector. Verify that the panel is

receiving power and functioning properly to prevent repetition of the

installation.

NOTE: Do not disconnect the connectors from the touch panel. The unit must be

installed with the attached connectors before being inserted into the drywall.

10. Insert the NXD-500IW back into the back box.

11. The microphone cable is taped to the back box. Connect the microphone cable

to its connector, making sure that the cable does not interfere with

reattachment of the bezel.

12. Carefully replace the two Plastite screws holding the device to the back box.

13. Place the bezel/Trim Ring assembly back onto the device. Make sure to align

the Microphone, Light, and PIR Motion sensor locations to their respective

openings on the bezel.

14. Reconnect the terminal Ethernet and USB to their respective locations on

either the Ethernet port or NetLinx Master.

Installing the NXD-500IW into a Flat Surface using #4 screws

Three #4 mounting screws (not included) are secured through circular holes located

at the left and right sides of the NXD-500IW. The most important thing to remember

when mounting the NXD-500IW is that the outer frame (Mounting Tabs) must be

installed flush against the mounting surface.

• Refer to SP-2261-02 for detailed installation dimensions.

• Cutting out the surface slightly smaller than what is outlined in the installation

drawings in order to make any necessary cutout adjustments, is highly

recommended.

1. Prepare the area by removing any screws or nails from the surface before

beginning the cutout process.

2. Cut out the surface for the NXD-500IW.

3. Remove the bezel from the NXD-500IW.

4. Gently unscrew the lower right-hand screw attaching the NXD-500IW to its

back box. These are at the bottom of the device, underneath the touch screen.

Gently remove the NXD-500IW from the back box.

5. Thread the incoming Ethernet and USB wiring from their terminal sources

through the surface opening. Leave enough slack in the wiring to

accommodate any re-positioning of the panel.

6. Connect the Ethernet and USB connectors to their corresponding locations

along the left side of the un-powered NXD-500IW touch panel. The USB

connectors can be from either a USB extension cable or a wireless USB RF

transmitter.

NOTE: Do not disconnect the connectors from the touch panel. The unit must be

installed with the necessary connectors before being inserted into the solid surface.

7. Carefully slide the main unit into the cutout until the Mounting Tabs of the

NXD-500i lie flush against the wall.

8. Insert and secure three #4 Mounting Screws (not included) into the

corresponding holes located along the sides of the NXD-500IW, using a

grounded Phillips-head screwdriver, until the unit is secure and flush against

the wall.

9. The microphone cable is taped to the back box. Connect the microphone cable

to its connector, making sure that the cable does not interfere with 

reattachment of the bezel.

10. Carefully replace the two Plastite screws holding the device to the back box.

11. Place the bezel back onto the device. Make sure to align the Microphone,

Light, and PIR Motion sensor locations to their respective openings on the

bezel.

12. Reconnect the terminal Ethernet and USB to their respective locations on

either the Ethernet port or NetLinx Master.

FIG. 3 NXD-500IW backbox with closed and open locking tabs

Locking tabs - Closed Locking tabs - Open

Locking tab screws

Produktspezifikationen

Marke:	AMX
Kategorie:	Monitor
Modell:	NXD-500iW-MW
Touchscreen:	Ja
Bildschirmdiagonale:	5 "
Eingebaute Lautsprecher:	Ja
Produktfarbe:	Weiß
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Zertifizierung:	FCC 15 B, CE, IEC 60950, RoHS
Stromverbrauch (Standardbetrieb):	5.5 W
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Bildschirmform:	Flach
Helligkeit:	200 cd/m²
Kontrastverhältnis:	250:1
Anzahl der Lautsprecher:	2
Temperaturbereich bei Lagerung:	-20 - 60 °C
Luftfeuchtigkeit bei Lagerung:	5 - 85 %
Gewicht (ohne Ständer):	360 g
Abmessungen (BxTxH):	142 x 50 x 105 mm
Seitenverhältnis:	16:9
Wandmontage:	Ja
NVIDIA G-SYNC:	Nein
Pixel Abstand:	0.14 x 0.14 mm
AMD FreeSync:	Nein
Display, sichtbarer Bereich BxH:	109.2 x 65.2 mm
Anzahl der vorgeschalteten Steckplätze:	1
Display-Auflösung:	800 x 480 Pixel